Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054849 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio and display receiver assembly via this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

E229861
0.813,0.813 1.24,0.969 0.427,0.156 10 AUXO 0.896,1.281 1.323,1.438 0.427,0.156 10 ARO 0.938,1.75 1.365,1.906 0.427,0.156 10 ALO 0.813,2.229 1.24,2.385 0.427,0.156 10 ASGN 0.813,2.708 1.24,2.865 0.427,0.156 10 AGND 2.552,2.844 3.323,3.083 0.771,0.24 10 Shielded 4.063,2.865 4.719,3.021 0.656,0.156 10 Shielded 5.927,0.729 6.354,0.885 0.427,0.156 10 ADPG 5.927,1.219 6.354,1.375 0.427,0.156 10 VAR+ 5.688,0.677 5.865,0.833 0.177,0.156 10 25 5.698,1.167 5.875,1.323 0.177,0.156 10 26 5.698,1.625 5.875,1.781 0.177,0.156 10 28 5.698,2.115 5.875,2.271 0.177,0.156 10 27 5.698,2.583 5.875,2.74 0.177,0.156 10 11 1.323,0.688 1.5,0.844 0.177,0.156 10 8 1.323,1.146 1.5,1.302 0.177,0.156 10 5 1.323,1.615 1.5,1.771 0.177,0.156 10 6 1.323,2.083 1.5,2.24 0.177,0.156 10 7 1.323,2.594 1.5,2.75 0.177,0.156 10 9 0.438,3.219 0.792,3.375 0.354,0.156 10 G145 0.417,3.385 1.604,3.781 1.188,0.396 10 No. 1 Stereo Jack Adapter Assembly 5.802,3.354 7.031,3.729 1.229,0.375 10 Radio and Display Receiver Assembly 5.927,1.667 6.354,1.823 0.427,0.156 10 VAL+ 5.927,2.177 6.354,2.333 0.427,0.156 10 VA- 5.927,2.635 6.354,2.792 0.427,0.156 10 AGND 5.802,3.177 6.313,3.365 0.51,0.188 10 G143

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the G145 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G145-8 (AUXO) - G143-25 (ADPG) Always Below 1 Ω
G145-5 (ARO) - G143-26 (VAR+) Always Below 1 Ω
G145-6 (ALO) - G143-28 (VAL+) Always Below 1 Ω
G145-7 (ASGN) - G143-27 (VA-) Always Below 1 Ω
G145-9 (AGND) - G143-11 (AGND) Always Below 1 Ω
G145-8 (AUXO) - Body ground Always 10 kΩ or higher
G145-5 (ARO) - Body ground Always 10 kΩ or higher
G145-6 (ALO) - Body ground Always 10 kΩ or higher
G145-7 (ASGN) - Body ground Always 10 kΩ or higher
G145-9 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR