Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM
RM30B0U _51 Engine / Hybrid System _010069 CRUISE CONTROL _0054851 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  C1AA6  Yaw Rate Sensor Zero Point Malfunction  


DESCRIPTION

The yaw rate sensor is integrated with airbag sensor assembly. the brake actuator assembly (skid control ECU) sends the vehicle stability signals to the lane departure warning camera. If the brake actuator assembly (skid control ECU) detects that the yaw rate sensor is malfunctioning, the brake actuator assembly (skid control ECU) sends a malfunction signal to the lane departure warning camera via the CAN communication and the lane departure warning camera stores DTC C1AA4, C1AA5 or C1AA6.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA4 Yaw Rate Sensor Circuit While driving with the lane departure alert system activated and the lane departure alert main switch on, a yaw rate sensor malfunction signal sent from the brake actuator assembly (skid control ECU) to the lane departure warning camera is detected for 5 seconds or more.
·

Vehicle stability control system

·

Lane departure warning camera


C1AA5 Yaw Rate Sensor Power Supply Voltage Circuit While driving with the lane departure alert system activated and the lane departure alert main switch on, a yaw rate sensor power supply voltage malfunction signal sent from the brake actuator assembly (skid control ECU) to the lane departure warning camera is detected for 5 seconds or more.
·

Vehicle stability control system

·

Lane departure warning camera


C1AA6 Yaw Rate Sensor Zero Point Malfunction While driving with the lane departure alert system activated and the lane departure alert main switch on, a yaw rate sensor zero point malfunction signal sent from the brake actuator assembly (skid control ECU) to the lane departure warning camera is detected for 5 seconds or more.
·

Vehicle stability control system

·

Lane departure warning camera



CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT

·

The lane departure alert system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the lane departure alert system after confirming that the communication systems are functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC (ABS/VSC/TRAC)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis/ ABS/VSC/TRAC / Trouble Codes.


d.

Check if DTCs are output.

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105

Result:
Proceed to
Vehicle stability control DTCs are not output
Vehicle stability control system DTCs are output



Vehicle stability control DTCs are not output

2.CLEAR DTC

Vehicle stability control system DTCs are output

2.CLEAR DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / Lane Departure Alert / Clear DTCs.


d.

Clear the DTCs.

Chassis > Lane Departure Alert > Clear DTCs
50002 355

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle at a speed between 50 km/h (32 mph) and 220 km/h (138 mph) and operate the lane departure alert system.



b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Chassis / Lane Departure Alert / Trouble Codes.


e.

Check for DTCs.

Chassis > Lane Departure Alert > Trouble Codes
50001 355

Result:
Proceed to
No DTCs are output
DTC C1AA4, C1AA5 and/or C1AA6 are output



No DTCs are output

DTC C1AA4, C1AA5 and/or C1AA6 are output