Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM30B0U _58 Vehicle Interior _009409 SEAT _0054863 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2658 Short in Sensor with Motor Power Supply Circuit Problem with the voltage supplied to the position control sensor.
·

Position control ECU and switch assembly

·

Separate type front seat cushion spring assembly

·

Separate type front seatback spring assembly

·

Harness or connector



WIRING DIAGRAM

B270910
1.354,1.573 1.615,1.75 0.26,0.177 10 e12 1.354,1.719 2.104,1.896 0.75,0.177 10 Slide Motor 5.219,1.271 5.688,1.438 0.469,0.167 10 SGND 5.219,0.719 5.688,0.885 0.469,0.167 10 SSRS 2.292,0.625 2.51,0.781 0.219,0.156 10 2 2.292,1.188 2.51,1.344 0.219,0.156 10 3 5.021,0.615 5.188,0.833 0.167,0.219 10 5 1.354,7.135 1.615,7.313 0.26,0.177 10 f1 1.354,7.292 2.354,7.469 1,0.177 10 Reclining Motor 5.219,6.469 5.688,6.635 0.469,0.167 10 SSRR 2.302,2.292 2.521,2.448 0.219,0.156 10 2 2.302,2.677 2.521,2.833 0.219,0.156 10 3 4.938,6.365 5.115,6.521 0.177,0.156 10 11 1.354,3.073 1.604,3.25 0.25,0.177 10 e13 1.354,3.229 2.604,3.406 1.25,0.177 10 Front Vertical Motor 5.219,2.396 5.688,2.563 0.469,0.167 10 SSFV 2.302,3.802 2.521,3.958 0.219,0.156 10 2 2.302,4.188 2.521,4.344 0.219,0.156 10 3 5.021,2.281 5.188,2.5 0.167,0.219 10 3 1.354,4.583 1.615,4.76 0.26,0.177 10 e14 1.354,4.729 2.104,4.906 0.75,0.177 10 Lifter Motor 5.219,3.906 5.688,4.073 0.469,0.167 10 SSRL 2.302,6.365 2.521,6.521 0.219,0.156 10 2 2.302,6.75 2.521,6.906 0.219,0.156 10 3 5.021,3.792 5.156,3.99 0.135,0.198 10 4 5.021,1.167 5.375,1.417 0.354,0.25 10 1 0.781,5.365 2.917,5.813 2.135,0.448 10 Separate Type Front Seat Cushion Spring Assembly 0.906,7.948 2.813,8.396 1.906,0.448 10 Separate Type Front Seatback Spring Assembly 5.031,8.021 7.083,8.521 2.052,0.5 10 Position Control ECU and Switch Assembly 5.031,7.865 5.292,8.021 0.26,0.156 10 e6

PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Proceed to
DTC B2658 is not output
DTC B2658 is output



DTC B2658 is not output

DTC B2658 is output

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)
2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - SLIDE MOTOR)
a.

Disconnect the e6 position control ECU and switch assembly connector.


b.

Disconnect the e12 slide motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-5 (SSRS) - e12-2 Always Below 1 Ω
e6-1 (SGND) - e12-3 Always Below 1 Ω
e6-5 (SSRS) - e6-1 (SGND) Always 10 kΩ or higher
e6-5 (SSRS) - Body ground Always 10 kΩ or higher
e6-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (SLIDE MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e12-2 - e12-3 Sliding switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT VERTICAL MOTOR)
a.

Disconnect the e13 front vertical motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-3 (SSFV) - e13-2 Always Below 1 Ω
e6-1 (SGND) - e13-3 Always Below 1 Ω
e6-3 (SSFV) - e6-1 (SGND) Always 10 kΩ or higher
e6-3 (SSFV) - Body ground Always 10 kΩ or higher
e6-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (FRONT VERTICAL MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e13-2 - e13-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - LIFTER MOTOR)
a.

Disconnect the e14 lifter motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-4 (SSRL) - e14-2 Always Below 1 Ω
e6-1 (SGND) - e14-3 Always Below 1 Ω
e6-4 (SSRL) - e6-1 (SGND) Always 10 kΩ or higher
e6-4 (SSRL) - Body ground Always 10 kΩ or higher
e6-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (LIFTER MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
e14-2 - e14-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

8.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

8.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
a.

Temporarily replace the separate type front seat cushion spring assembly with a new or normally functioning one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

c.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Proceed to
DTC B2658 is not output
DTC B2658 is output



DTC B2658 is not output

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY WAS DEFECTIVE)

DTC B2658 is output

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - RECLINING MOTOR)
a.

Disconnect the e6 position control ECU and switch assembly connector.


b.

Disconnect the f1 reclining motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e6-11 (SSRR) - f1-2 Always Below 1 Ω
e6-1 (SGND) - f1-3 Always Below 1 Ω
e6-11 (SSRR) - e6-1 (SGND) Always 10 kΩ or higher
e6-11 (SSRR) - Body ground Always 10 kΩ or higher
e6-1 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
f1-2 - f1-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

11.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

11.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
a.

Temporarily replace the separate type front seatback spring assembly with a new or normally functioning one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

c.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162

Result:
Proceed to
DTC B2658 is not output
DTC B2658 is output



DTC B2658 is not output

END (SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY WAS DEFECTIVE)

DTC B2658 is output

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY