Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM30B0U _58 Vehicle Interior _009409 SEAT _0054863 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Front Power Seat does not Operate with Front Power Seat Switch  


DESCRIPTION

Signals are input into the position control ECU and switch assembly. The built-in ECU manages the signals received from the power seat switch assembly and operates each motor. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM

B342198
0.521,0.75 1.375,0.979 0.854,0.229 10 false from Battery 2.021,1.021 2.969,1.198 0.948,0.177 10 false P/SEAT F/R*1 2,1.344 2.938,1.552 0.938,0.208 10 false P/SEAT F/L*2 0.167,1.938 1.542,2.156 1.375,0.219 10 false *1: for TMC Made 0.167,2.323 1.771,2.531 1.604,0.208 10 false *2: for TMMC Made 4.344,0.656 4.5,0.854 0.156,0.198 10 false 7 4.354,1.219 4.51,1.417 0.156,0.198 10 false 2 4.542,0.75 4.854,0.948 0.313,0.198 10 false +B1 4.542,1.333 5,1.531 0.458,0.198 10 false GND1 3.719,1.896 4.177,2.094 0.458,0.198 10 false e18 3.708,2.104 6.469,2.313 2.76,0.208 10 false Position Control ECU and Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the power seat switch assembly.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Proceed to
All power seat functions do not operate
One or more power seat functions do not operate




All power seat functions do not operate

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY)

One or more power seat functions do not operate

GO TO OTHER DIAGNOSIS PROCEDURE (One or more Power Seat Motors do not Operate)

2.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the e18 position control ECU and switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e18-7 (+B1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e18-2 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR