Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM30B0U _59 Vehicle Exterior _010076 WINDOW / GLASS _0054872 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

w/ Jam Protection Function:

i.
E268551
1,1.25 1,0.333 1,0.333 1.167,0.333 true 2.188,1.417 2.5,0.917 false 3.167,1.417 2.833,0.917 false 2.25,0.563 2.5,0.563 false 2.813,0.563 3.146,0.844 false 1.24,0.26 1.552,0.458 0.313,0.198 10 *1 2.021,0.01 2.333,0.208 0.313,0.198 10 *a 2.125,0.49 2.281,0.688 0.156,0.198 10 B 3.052,0.854 3.375,1.052 0.323,0.198 10 GND 2.083,1.448 2.406,1.646 0.323,0.198 10 UP 2.906,1.458 3.406,1.656 0.5,0.198 10 DOWN
*1 Motor Gear
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
V100135

Clockwise
V100136

Counterclockwise


Apply positive (+) battery voltage to the connector terminal 2 (B).


ii.

Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) / 10 (UP).

NOTICE:
·

Do not apply voltage to any terminals except terminals 1 and 2, to avoid damaging the pulse sensor inside the motor.


·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.




iii.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (B)
Battery negative (-): 1 (GND) (3 seconds or more) → 1 (GND) and 10 (UP) (within 1 second) → 1 (GND) (within 1 second) → 1 (GND) and 10 (UP)
Motor gear rotates clockwise (UP)
Battery positive (+) → 2 (B)
Battery negative (-): 1 (GND) (3 seconds or more) → 1 (GND) and 7 (DOWN) (within 1 second) → 1 (GND) (within 1 second) → 1 (GND) and 7 (DOWN)
Motor gear rotates counterclockwise (DOWN)




b.

w/o Jam Protection Function:

i.
E270262
1.01,1.281 1,0.25 1,0.25 1.25,0.25 true 2.167,0.75 2.417,0.75 true 2.917,0.75 3.167,0.75 true 1.292,0.177 1.604,0.333 0.313,0.156 10 *1 0.052,0.052 0.365,0.208 0.313,0.156 10 *a 2.031,0.677 2.188,0.875 0.156,0.198 10 U 3.208,0.667 3.365,0.865 0.156,0.198 10 D
*1 Motor Gear
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
V100135

Clockwise
V100136

Counterclockwise


Apply battery voltage to connector terminals 1 (D) and 2 (U).

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).




c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D)
Motor gear rotates clockwise
Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U)
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
E268557
2.292,0.51 2.542,0.677 true 3.229,0.5 3,0.677 true 0.833,0.917 0.833,0.25 0.833,0.25 1,0.25 false 1.063,0.177 1.375,0.333 0.313,0.156 10 *1 0.052,0.021 0.365,0.177 0.313,0.156 10 *a 2.167,0.417 2.479,0.573 0.313,0.156 10 U 3.271,0.406 3.396,0.552 0.125,0.146 10 D
*1 Motor Gear
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
V100135

Clockwise
V100136

Counterclockwise


Apply battery voltage to connector terminals 1 (D) and 2 (U).

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).



b.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U)
Motor gear rotates clockwise
Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D)
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly RH.