Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM30B0U _59 Vehicle Exterior _010075 WIPER / WASHER _0054887 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

a.

Check the front wiper intermittent operation.

i.
E257039
0.427,0.99 0.76,1.24 0.333,0.25 2.615,1 2.948,1.25 0.333,0.25 1.24,1.083 0.99,0.479 false 2.719,1.76 2.385,1.313 false 0.083,0.125 0.396,0.323 0.313,0.198 10 *a 0.49,1.031 0.802,1.229 0.313,0.198 10 G11 2.667,1.042 2.979,1.24 0.313,0.198 10 G10 0.844,0.313 1.156,0.51 0.313,0.198 10 +1 2.656,1.792 2.969,1.99 0.313,0.198 10 EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G11-3 (+1) and a negative (-) lead to terminal G10-4 (EW).


ii.

Turn the wiper switch to the INT position.


iii.

Operate the intermittent wiper and check the voltage between terminals G11-3 (+1) and G10-4 (EW).

OK:

Voltage changes as shown in the illustration.


E136493
2.625,0.104 3.104,0.271 0.479,0.167 10 FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 Start 0.115,0.604 1.906,1.281 1.792,0.677 10 Voltage between terminals G11-3 (+1) and G10-4 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 1.6 +/- 1 second 5.792,1 7.021,1.198 1.229,0.198 10 10.7 +/- 5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 Start 4.792,1.385 5.146,1.563 0.354,0.177 10 Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer operation.

i.
E257039
0.427,0.99 0.76,1.24 0.333,0.25 2.615,1 2.948,1.25 0.333,0.25 1.24,1.083 0.99,0.479 false 2.719,1.76 2.385,1.313 false 0.083,0.125 0.396,0.323 0.313,0.198 10 *a 0.49,1.031 0.802,1.229 0.313,0.198 10 G11 2.667,1.042 2.979,1.24 0.313,0.198 10 G10 0.844,0.313 1.156,0.51 0.313,0.198 10 +1 2.656,1.792 2.969,1.99 0.313,0.198 10 EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal G11-3 (+1) and a negative (-) lead to terminal G10-4 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals G11-3 (+1) and G10-4 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.99,0.885 2.719,1.219 1.729,0.333 10 Voltage between terminals G11-3 (+1) and G10-4 (EW): 1.698,0.281 2.958,0.552 1.26,0.271 10 Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 OFF 3.354,0.188 3.729,0.365 0.375,0.177 10 ON

If the result is not as specified, replace the windshield wiper switch assembly.