1.INSPECT NO. 1 HEATER CONTROL SUB-ASSEMBLY
| *a | Component without harness connected
(No. 1 Heater Control Sub-assembly) |
| *b | Recirculation/fresh Switch |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (FRS) - 4 (REC) | Recirculation/fresh switch: OFF | Below 1 Ω |
| 3 (FRS) - 4 (REC) | Recirculation/fresh switch: ON | 10 kΩ or higher |
| 5 (LED+) - 4 (REC) | Recirculation/fresh switch: OFF | 10 kΩ or higher |
| 5 (LED+) - 4 (REC) | Recirculation/fresh switch: ON | Below 30 Ω |
If the result is not as specified, replace the No. 1 heater control sub-assembly.
Check that the recirculation/fresh indicator light comes on.
Turn the recirculation/fresh switch to ON.
Connect a positive (+) lead from the battery to terminal 2 (A/C+) and negative (-) lead to terminal 4 (REC), and check that the recirculation/fresh indicator light comes on.
The indicator light comes on.
If the result is not as specified, replace the No. 1 heater control sub-assembly.
Check that the illumination light comes on.
Connect a positive (+) lead from the battery to terminal 7 (ILL+) and negative (-) lead to terminal 6 (ILL-), and check that the illumination light comes on.
The illumination light comes on.
If the result is not as specified, replace the No. 1 heater control sub-assembly.
2.INSPECT NO. 2 HEATER CONTROL SUB-ASSEMBLY
| *a | Component without harness connected
(No. 2 Heater Control Sub-assembly) |
| *b | Rear Window Defogger Switch |
| *1 | Blower Switch OFF Position |
| *2 | Blower Switch LO Position |
| *3 | Blower Switch M1 Position |
| *4 | Blower Switch M2 Position |
| *5 | Blower Switch HI Position |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (LO), 6 (HI), 9 (M1), 10 (M2) - 5 (E) | Blower switch: 0 | 10 kΩ or higher |
| 4 (LO) - 5 (E) | Blower switch: 1 | Below 1 Ω |
| 4 (LO), 9 (M1) - 5 (E) | Blower switch: 1 - 2 | Below 1 Ω |
| 4 (LO), 9 (M1) - 5 (E) | Blower switch: 2 | Below 1 Ω |
| 4 (LO), 9 (M1), 10 (M2) - 5 (E) | Blower switch: 2 - 3 | Below 1 Ω |
| 4 (LO), 10 (M2) - 5 (E) | Blower switch: 3 | Below 1 Ω |
| 4 (LO), 10 (M2), 6 (HI) - 5 (E) | Blower switch: 3 - 4 | Below 1 Ω |
| 4 (LO), 6 (HI) - 5 (E) | Blower switch: 4 | Below 1 Ω |
| 2 (RDEF) - 5 (E) | Rear window defogger switch: OFF | 10 kΩ or higher |
| 2 (RDEF) - 5 (E) | Rear window defogger switch: ON | Below 20 Ω |
If the result is not as specified, replace the No. 2 heater control sub-assembly.
Check that the rear window defogger switch indicator light comes on.
Connect a positive (+) lead from the battery to terminal 3 (IG+) and negative (-) lead to terminal 5 (E).
Push the rear window defogger switch in and check that the indicator light comes on.
The indicator light comes on.
If the result is not as specified, replace the No. 2 heater control sub-assembly.
Check that the illumination light comes on.
Connect a positive (+) lead from the battery to terminal 7 (ILL+) and negative (-) lead to terminal 1 (ILL-), and check that the illumination light comes on.
The illumination light comes on.
If the result is not as specified, replace the No. 2 heater control sub-assembly.
3.INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY
| *a | Component without harness connected
(No. 3 Heater Control Sub-assembly) |
| *b | A/C Switch |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (B) - 3 (A/C) | A/C switch: ON | Below 20 Ω |
| 2 (B) - 3 (A/C) | A/C switch: OFF | 10 kΩ or higher |
If the result is not as specified, replace the No. 3 heater control sub-assembly.
Check that the indicator light comes on.
Turn the No. 3 heater control sub-assembly (A/C switch) to the ON position.
Connect a positive (+) lead from the battery to terminal 2 (B) and negative (-) lead to terminal 4 (AIND), and check that the indicator light comes on.
The indicator light comes on.
If the result is not as specified, replace the No. 3 heater control sub-assembly.
Check that the illumination light comes on.
Connect a positive (+) lead from the battery to terminal 5 (ILL+) and negative (-) lead to terminal 6 (ILL-), and check that the illumination light comes on.
The illumination light comes on.
If the result is not as specified, replace the No. 3 heater control sub-assembly.