Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0055011 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



a.

Visually check for defects with the spiral cable sub-assembly.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector


OK:

No defects are found.


If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.
B341170
0.292,1.229 0.646,1.448 0.354,0.219 1.042,1.24 1.396,1.458 0.354,0.219 2.104,0.26 2.458,0.479 0.354,0.219 2.677,0.26 3.031,0.479 0.354,0.219 1.802,3.281 2.156,3.5 0.354,0.219 2.292,3.208 2.646,3.427 0.354,0.219 2.698,2 3.115,1.583 true 3.104,1.448 3.417,1.604 0.313,0.156 10 *1 0.104,0.083 0.417,0.24 0.313,0.156 10 *a 0.385,1.25 0.698,1.448 0.313,0.198 10 z2 1.135,1.26 1.448,1.458 0.313,0.198 10 z3 2.208,0.281 2.521,0.479 0.313,0.198 10 z1 2.771,0.281 3.083,0.479 0.313,0.198 10 z4 1.875,3.313 2.188,3.51 0.313,0.198 10 G9 2.365,3.24 2.677,3.438 0.313,0.198 10 G8
*1 Interlock
*a Component without harness connected
(Spiral Cable Sub-assembly)


Check the spiral cable sub-assembly.

NOTICE:

When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.


i.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 - z4-3 Always 3 Ω or less
G8-2 - z4-4 Always 3 Ω or less
G8-3 - z1-8 Always 3 Ω or less
G8-4 - z1-9 Always 3 Ω or less
G8-5 - z1-10 Always 3 Ω or less
G8-6 - z1-11 Always 3 Ω or less
G8-9 - z1-1 Always 3 Ω or less
G8-10 - z1-2 Always 3 Ω or less
G8-11 - z1-3 Always 3 Ω or less
G8-13 - z1-5 Always 3 Ω or less
G9-1 - z3-2 Always Below 1 Ω
G9-2 - z3-1 Always Below 1 Ω
G9-3 - z2-1 Always Below 1 Ω
G9-4 - z2-2 Always Below 1 Ω



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 - z4-3 Always 3 Ω or less
G8-2 - z4-4 Always 3 Ω or less
G8-3 - z1-8 Always 3 Ω or less
G8-4 - z1-9 Always 3 Ω or less
G8-5 - z1-10 Always 3 Ω or less
G8-6 - z1-11 Always 3 Ω or less
G8-9 - z1-1 Always 3 Ω or less
G8-10 - z1-2 Always 3 Ω or less
G8-11 - z1-3 Always 3 Ω or less
G8-13 - z1-5 Always 3 Ω or less
G9-1 - z3-2 Always Below 1 Ω
G9-2 - z3-1 Always Below 1 Ω
G9-3 - z2-1 Always Below 1 Ω
G9-4 - z2-2 Always Below 1 Ω



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 - z4-3 Always 3 Ω or less
G8-2 - z4-4 Always 3 Ω or less
G8-3 - z1-8 Always 3 Ω or less
G8-4 - z1-9 Always 3 Ω or less
G8-5 - z1-10 Always 3 Ω or less
G8-6 - z1-11 Always 3 Ω or less
G8-9 - z1-1 Always 3 Ω or less
G8-10 - z1-2 Always 3 Ω or less
G8-11 - z1-3 Always 3 Ω or less
G8-13 - z1-5 Always 3 Ω or less
G9-1 - z3-2 Always Below 1 Ω
G9-2 - z3-1 Always Below 1 Ω
G9-3 - z2-1 Always Below 1 Ω
G9-4 - z2-2 Always Below 1 Ω


If the result is not as specified, replace the spiral cable with sensor sub-assembly.