Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM30B0U _59 Vehicle Exterior _009987 SLIDING ROOF / CONVERTIBLE _0056327 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.
B338927
0.615,1.094 0.75,1.094 0.75,1.094 0.75,0.885 false 0.313,0.865 0.406,0.865 0.406,0.865 0.406,0.698 false 0.125,0.781 0.438,0.938 0.313,0.156 10 *1 0.417,1.021 0.729,1.177 0.313,0.156 10 *2
*1 Guide
*2 Pin


Detach the claw.


b.

Detach the guide and pin, and remove the map light bracket.


c.
B338928

Remove the 2 bolts and sliding roof drive gear sub-assembly.


Hide 2.REMOVE SUNSHADE TRIM SUB-ASSEMBLY

a.
B338929

Remove the screw and the sliding roof piece sub-assembly LH.

HINT:

Use the same procedure for the RH side.



b.
B338930

Slide and remove the sunshade trim sub-assembly.


Hide 3.REMOVE REAR ROOF DRIP CHANNEL

a.
B338931
1.083,0.573 1.271,0.573 false 0.802,2.646 0.99,2.646 false 1.323,0.51 1.635,0.667 0.313,0.156 10 *1 0.615,2.573 0.927,2.729 0.313,0.156 10 *1
*1 Protective Tape


Using a screwdriver, detach the 2 claws. Then slide the rear roof drip channel rearward to remove it.

HINT:

Tape the screwdriver tip before use.



Hide 4.REMOVE SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

NOTICE:

Do not disassemble the sliding roof drive cable sub-assembly except when replacing it.


a.
B338932

Hold down the roof wind deflector panel sub-assembly.


b.
B338933
1.375,1.646 1.583,1.646 1.583,1.646 2,1.406 false 1.104,1.583 1.417,1.74 0.313,0.156 10 *1
*1 Protective Tape


Using a screwdriver, slide the sliding roof drive cable sub-assembly in the direction indicated by the arrow in the illustration to remove it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the other sliding roof drive cable sub-assembly.




Hide 5.REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
B338934
2.573,1.438 2.406,1.438 false 2.396,1.875 2.229,1.875 false 0.542,0.292 0.646,0.292 0.646,0.292 0.646,0.427 false 0.24,0.438 0.344,0.438 0.344,0.438 0.344,0.573 false 0.385,0.208 0.698,0.365 0.313,0.156 10 *1 0.073,0.375 0.385,0.531 0.313,0.156 10 *2 2.229,1.365 2.542,1.521 0.313,0.156 10 *1 2.073,1.802 2.385,1.958 0.313,0.156 10 *2 1.833,0.146 2.146,0.302 0.313,0.156 10 (2) 0.708,1.844 0.927,2 0.219,0.156 10 (1)
*1 Spring
*2 Guide


Pull the spring in the direction indicated by the arrow (1) in the illustration to detach the 2 springs.


b.

Pull the roof wind deflector panel sub-assembly in the direction indicated by the arrow (2) in the illustration to detach the 2 guides and remove it.