Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM30B0U _59 Vehicle Exterior _009987 SLIDING ROOF / CONVERTIBLE _0056327 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY

a.
B338935
0.656,0.396 0.656,0.188 0.656,0.188 0.531,0.188 false 0.406,0.583 0.406,0.375 0.406,0.375 0.281,0.375 false 2.354,1.438 2.563,1.438 false 2.198,1.875 2.406,1.875 false 0.104,0.302 0.417,0.458 0.313,0.156 10 *1 0.354,0.125 0.667,0.281 0.313,0.156 10 *2 2.021,1.792 2.333,1.948 0.313,0.156 10 *1 2.188,1.354 2.5,1.51 0.313,0.156 10 *2 1.885,0.146 2.198,0.354 0.313,0.208 10 (1) 0.323,1.698 0.635,1.906 0.313,0.208 10 (2)
*1 Guide
*2 Spring


Attach the 2 guides in the direction indicated by the arrow (1) in the illustration to install the roof wind deflector panel sub-assembly.


b.

Attach the 2 springs in the direction indicated by the arrow (2) in the illustration.

NOTICE:

Make sure that the springs are securely installed.



Hide 2.INSTALL SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY

a.
B338932

Hold down the roof wind deflector panel sub-assembly.


b.
B338936
2.26,1.135 2.417,1.135 2.417,1.135 2.729,1.198 true 2.052,1.063 2.365,1.219 0.313,0.156 10 *1
*1 Protective Tape


Using a screwdriver, slide the sliding roof drive cable sub-assembly in the direction indicated by the arrow in the illustration to install it.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the other sliding roof drive cable sub-assembly.




Hide 3.INSTALL REAR ROOF DRIP CHANNEL

a.
B338937
2.271,1.208 2.573,1.375 0.302,0.167 10 (1) 0.729,1 1.031,1.167 0.302,0.167 10 (2) 1.146,3.083 1.448,3.25 0.302,0.167 10 (2)

Insert the rear roof drip channel in the direction indicated by the arrow (1) in the illustration.


b.

Attach the 2 claws in the direction indicated by the arrow (2) in the illustration to install the rear roof drip channel.


Hide 4.ADJUST FULLY CLOSED POSITION

a.
B338938
1.021,0.177 1.156,0.177 1.156,0.177 1.583,0.344 false 2.458,1.24 2.188,1.24 2.188,1.24 1.615,0.615 false 0.844,0.104 1.156,0.26 0.313,0.156 10 false *1 2.51,1.167 2.823,1.323 0.313,0.156 10 false *1
*1 Alignment Mark


Using a screwdriver, slide the sliding roof drive cable sub-assembly in either direction indicated by the arrows in the illustration and alignment marks.

HINT:

Tape the screwdriver tip before use.



Hide 5.INSTALL SUNSHADE TRIM SUB-ASSEMBLY

a.
B338939

Insert the sunshade trim sub-assembly into the sliding roof housing sub-assembly.


b.

Install the sliding roof piece sub-assembly LH with the screw.

HINT:

Use the same procedure for the RH side.



Hide 6.INSTALL SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

a.

Install the sliding roof drive gear sub-assembly with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Attach the guide and pin.


c.

Attach the claw and install the map light bracket.