Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2012.12–2013.11
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054849 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E271826
5.677,2.896 6.135,3.094 0.458,0.198 10 false G67 5.698,3.063 6.875,3.458 1.177,0.396 10 false Radio and Display Receiver Assembly 0.417,2.896 0.75,3.094 0.333,0.198 10 false M22 0.427,3.063 1.615,3.5 1.188,0.438 10 false Stereo Component Amplifier Assembly 6,0.552 6.313,0.75 0.313,0.198 10 false L- 6.021,1.052 6.333,1.25 0.313,0.198 10 false L+ 6.01,1.5 6.323,1.698 0.313,0.198 10 false R- 6.01,1.979 6.323,2.177 0.313,0.198 10 false R+ 1.094,0.552 1.406,0.75 0.313,0.198 10 false L- 1.094,1.042 1.406,1.24 0.313,0.198 10 false L+ 1.094,1.5 1.406,1.698 0.313,0.198 10 false R- 1.083,1.969 1.396,2.167 0.313,0.198 10 false R+ 0.979,2.448 1.438,2.646 0.458,0.198 10 false SLD 2.281,2.604 2.906,2.833 0.625,0.229 10 false Shielded 3.917,2.583 4.552,2.833 0.635,0.25 10 false Shielded 1.417,0.438 1.729,0.635 0.313,0.198 10 false 2 1.417,0.917 1.729,1.115 0.313,0.198 10 false 3 1.417,1.396 1.729,1.594 0.313,0.198 10 false 4 1.417,1.875 1.729,2.073 0.313,0.198 10 false 5 1.417,2.333 1.875,2.531 0.458,0.198 10 false 6 5.688,0.438 6,0.635 0.313,0.198 10 false 19 5.75,0.917 6.063,1.115 0.313,0.198 10 false 9 5.688,1.385 6,1.583 0.313,0.198 10 false 18 5.75,1.865 6.063,2.063 0.313,0.198 10 false 8

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G67 radio and display receiver assembly connector.


b.

Disconnect the M22 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M22-5 (R+) - G67-8 (R+) Always Below 1 Ω
M22-4 (R-) - G67-18 (R-) Always Below 1 Ω
M22-3 (L+) - G67-9 (L+) Always Below 1 Ω
M22-2 (L-) - G67-19 (L-) Always Below 1 Ω
M22-6 (SLD) - Body ground Always 10 kΩ or higher
M22-5 (R+) - Body ground Always 10 kΩ or higher
M22-4 (R-) - Body ground Always 10 kΩ or higher
M22-3 (L+) - Body ground Always 10 kΩ or higher
M22-2 (L-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR