Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM30B0U _58 Vehicle Interior _010074 SUPPLEMENTAL RESTRAINT SYSTEMS _0056337 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1790  Center Airbag Sensor Assembly Communication Circuit Malfunction  


DESCRIPTION

The airbag sensor assembly communication circuit consists of the occupant detection ECU and airbag sensor assembly.

DTC B1790 is stored when a malfunction is detected in the airbag sensor assembly communication circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1790 Center Airbag Sensor Assembly Communication Circuit Malfunction
One of the following conditions is met:
·

Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the airbag sensor assembly communication circuit for 2 seconds.

·

Airbag sensor assembly malfunction.

·

Occupant detection ECU malfunction.


·

Floor wire

·

Front seat wire RH

·

Occupant detection ECU

·

Airbag sensor assembly



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1790 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C238367
0.594,3.094 2.292,3.458 1.698,0.365 10 false Occupant Detection ECU 0.594,2.906 1.135,3.375 0.542,0.469 10 false d16 3.438,0.906 3.865,1.333 0.427,0.427 10 false Md1 3.521,0.708 3.792,1.031 0.271,0.323 10 false 1 3.521,1.885 3.781,2.323 0.26,0.438 10 false 5 3.427,2.083 3.844,2.479 0.417,0.396 10 false Md1 5.146,0.813 5.552,1.292 0.406,0.479 10 false 9 5.156,1.979 5.552,2.49 0.396,0.51 10 false 17 5.354,2.906 5.771,3.26 0.417,0.354 10 false M25 5.354,3.094 6.927,3.448 1.573,0.354 10 false Airbag Sensor Assembly 5.406,0.906 5.854,1.323 0.448,0.417 10 false FSR+ 5.385,2.083 5.802,2.479 0.417,0.396 10 false FSR- 1.854,0.781 2.313,1.354 0.458,0.573 10 false 7 1.865,1.958 2.219,2.281 0.354,0.323 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1790 is not output
DTC B1790 is output


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




DTC B1790 is not output

DTC B1790 is output

2.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant detection ECU and airbag sensor assembly.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

3.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTOR

3.CHECK CONNECTORS
a.
C256404
0.813,1.333 1.125,1.49 0.313,0.156 10 false *1 2.406,1.5 2.719,1.656 0.313,0.156 10 false *2
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly


Disconnect the connectors from the airbag sensor assembly and occupant detection ECU.


b.

Check that the connectors (on the airbag sensor assembly side and occupant detection ECU side) are not damaged.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

4.CHECK AIRBAG SENSOR ASSEMBLY CIRCUIT

Connectors are deformed or damaged

4.CHECK AIRBAG SENSOR ASSEMBLY CIRCUIT
a.
C256405
0.198,1.938 0.615,2.198 0.417,0.26 0.385,3.677 0.802,3.938 0.417,0.26 2.5,3.552 2.167,3.833 false 1.698,4.5 1.948,4.375 false 2.146,4.073 2.479,4.229 false 0.802,0.844 1.115,1 0.313,0.156 10 false *1 2.479,0.99 2.792,1.146 0.313,0.156 10 false *2 1.563,1.417 1.875,1.573 0.313,0.156 10 false *3 1.667,3.135 1.979,3.292 0.313,0.156 10 false *4 1.5,4.438 1.813,4.594 0.313,0.156 10 false *5 0.094,1.531 0.427,1.698 0.333,0.167 10 false *a 0.146,3.417 0.458,3.573 0.313,0.156 10 false *b 0.458,3.729 0.792,3.896 0.333,0.167 10 false M25 0.302,2 0.635,2.167 0.333,0.167 10 false d16 2.563,3.438 2.979,3.625 0.417,0.188 10 false FSR+ 2.552,4.177 3.052,4.375 0.5,0.198 10 false FSR- 2.208,0.271 2.521,0.427 0.313,0.156 10 false A 1.948,0.51 2.26,0.667 0.313,0.156 10 false B 1.656,0.51 1.969,0.667 0.313,0.156 10 false C 1.542,0.51 1.854,0.667 0.313,0.156 10 false D 1.25,0.521 1.563,0.677 0.313,0.156 10 false E 0.938,0.271 1.25,0.427 0.313,0.156 10 false F
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Connector E
*4 Connector B
*5 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d16-7 - Body ground Ignition switch ON Below 1 V
d16-4 - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 9 (FSR+) and 17 (FSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d16-7 - d16-4 Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d16-7 - d16-4 Always 1 MΩ or higher
d16-7 - Body ground
d16-4 - Body ground



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

10.CHECK FRONT SEAT WIRE RH
5.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1790 is not output
DTC B1790 is output


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




DTC B1790 is not output

DTC B1790 is output

6.REPLACE OCCUPANT DETECTION ECU
6.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

HINT:

Perform the inspection using parts from a normal vehicle when possible.



Result:
Proceed to
NEXT



NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

8.PERFORM SENSITIVITY CHECK
8.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

9.CHECK DTC
9.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1790 is not output
DTC B1790 is output


HINT:

DTCs other than DTC B1790 may be output at this time, but they are not related to this check.




DTC B1790 is not output

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)

DTC B1790 is output

10.CHECK FRONT SEAT WIRE RH
a.
E272030
0.135,3.531 0.573,3.781 0.438,0.25 0.104,1.833 0.542,2.083 0.438,0.25 1.875,2.76 2.021,2.917 false 1.25,0.219 1.563,0.375 0.313,0.156 10 false *1 1.729,0.229 2.042,0.385 0.313,0.156 10 false *2 0.656,0.917 0.969,1.073 0.313,0.156 10 false *3 2.406,1.094 2.719,1.25 0.313,0.156 10 false *4 2.063,2.854 2.375,3.01 0.313,0.156 10 false *5 1.51,1.469 1.823,1.625 0.313,0.156 10 false *6 1.583,2.906 1.896,3.063 0.313,0.156 10 false *7 0.135,1.479 0.448,1.635 0.313,0.156 10 false *a 0.115,3.177 0.427,3.333 0.313,0.156 10 false *b 0.198,1.875 0.51,2.031 0.313,0.156 10 false d16 0.229,3.573 0.542,3.729 0.313,0.156 10 false Md1 2.219,0.385 2.531,0.542 0.313,0.156 10 false A 1.906,0.594 2.219,0.75 0.313,0.156 10 false B 1.656,0.594 1.969,0.75 0.313,0.156 10 false C 1.448,0.594 1.76,0.75 0.313,0.156 10 false D 1.135,0.594 1.448,0.75 0.313,0.156 10 false E 0.813,0.375 1.125,0.531 0.313,0.156 10 false F
*1 Front Seat Wire RH
*2 Floor Wire
*3 Occupant Detection ECU
*4 Airbag Sensor Assembly
*5 Service Wire
*6 Connector E
*7 Connector D
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Floor Wire)


Disconnect the front seat wire RH connector from the floor wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Md1-1 - Body ground Ignition switch ON Below 1 V
Md1-5 - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the connector from the occupant detection ECU.


g.

Using a service wire, connect terminals 7 and 4 of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Md1-1 - Md1-5 Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Md1-1 - Md1-5 Always 1 MΩ or higher
Md1-1 - Body ground
Md1-5 - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT SEAT WIRE RH