Home › Vehicle Interior › LIGHTING (INT) › BACK DOOR COURTESY SWITCH
RM30B0U _58 Vehicle Interior _010070 LIGHTING (INT) _0057956 BACK DOOR COURTESY SWITCH G

LIGHTING (INT)  BACK DOOR COURTESY SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT BACK DOOR LOCK ASSEMBLY (BACK DOOR COURTESY SWITCH)

a.
B340482
1.948,1.656 2.417,1.427 true 2.583,1.406 2.969,1.25 true 1.292,1.563 1.698,1 true 0.792,1.552 0.469,1.333 true 0.417,2.333 1.01,1.813 true 2.573,1.271 2.969,0.615 true 2.438,1.26 1.781,0.479 true 0.073,0.031 0.385,0.188 0.313,0.156 10 *a 1.635,0.844 1.948,1 0.313,0.156 10 *b 0.323,1.188 0.635,1.344 0.313,0.156 10 *c 0.25,2.271 0.563,2.427 0.313,0.156 10 *d 1.969,2.688 2.281,2.844 0.313,0.156 10 *e 1.917,2.885 2.229,3.042 0.313,0.156 10 *f 1.781,3.5 2.063,3.76 0.281,0.26 10 *g 1.5,3.906 1.813,4.063 0.313,0.156 10 *h 3.01,1.156 3.344,1.344 0.333,0.188 10 CTY 1.823,1.594 1.979,1.792 0.156,0.198 10 E 1.656,0.313 1.99,0.5 0.333,0.188 10 M- 2.927,0.427 3.26,0.615 0.333,0.188 10 M+
*a Component without harness connected
(Back Door Lock Assembly (Back Door Courtesy Switch))
*b Clockwise
*c Counterclockwise
*d Drive Gear
*e Over-latch
*f Full-latch
*g Half-latch
*h Open-latch


w/ Power Back Door:

i.

Apply battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1 (M+)
Battery negative (-) → Terminal 2 (M-)
Latch turns to full-latch position (clockwise rotation)
Battery positive (+) → Terminal 2 (M-)
Battery negative (-) → Terminal 1 (M+)
Latch turns to open-latch position (counterclockwise rotation)



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CTY) - 4 (E) Over-latch 10 kΩ or higher
3 (CTY) - 4 (E) Full-latch 10 kΩ or higher
3 (CTY) - 4 (E) Half-latch 10 kΩ or higher
3 (CTY) - 4 (E) Open-latch Below 1 Ω


If the result is not as specified, replace the back door lock assembly (back door courtesy switch).



b.
B337032
1.927,3.719 2.271,4.031 true 1.729,3.74 1.76,4.115 true 1.552,3.74 1.198,4.042 true 0.958,3.052 1.271,3.208 0.313,0.156 10 *a 2.573,1.927 2.885,2.083 0.313,0.156 10 *b 2.615,0.979 2.927,1.135 0.313,0.156 10 *c 1.073,4.063 1.385,4.26 0.313,0.198 10 D+ 1.625,4.135 2.24,4.333 0.615,0.198 10 ACT+ 2.208,4.052 2.823,4.25 0.615,0.198 10 ACT-
*a Component without harness connected
(Back Door Lock Assembly (Back Door Courtesy Switch))
*b Unlock
*c Lock


w/o Power Back Door:

i.

Move the back door lock assembly to the lock position.


ii.

Apply battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 2 (ACT+)
Battery negative (-) → Terminal 1 (ACT-)
Unlock



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (D+) - 1 (ACT-) Lock 10 kΩ or higher
3 (D+) - 1 (ACT-) Unlock Below 1 Ω


If the result is not as specified, replace the back door lock assembly (back door courtesy switch).