Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  U0073  Control Module Communication Bus OFF  U0100  Lost Communication with ECM  U0124  Lost Communication with Lateral Acceleration Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives the signals from the ECM, steering angle sensor (spiral with sensor cable sub-assembly), and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus OFF When any of the following is detected:
1.

The condition that the bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession while the voltage at the IG1 terminal is between 10 and 17.4 V. (Sent signals cannot be received.)

2.

When the IG1 terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 1 second or more.

3.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

·

The condition that a delay in receiving data from the yaw rate sensor and steering angle sensor occurs more than once within 5 seconds.



CAN communication system
U0100 Lost Communication with ECM When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more. CAN communication system
U0124 Lost Communication with Lateral Acceleration Sensor Module When either of the following is detected:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

·

The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.



CAN communication system
U0126 Lost Communication with Steering Angle Sensor Module When either of the following is detected:
1.

When the IG1 terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.

2.

When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

·

The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds.



CAN communication system

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRAC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open ECM communication open detection Normal or Error Normal Error: Momentary interruption
Yaw Rate Open Yaw rate sensor open detection Normal or Error Normal Error: Momentary interruption
Deceleration Open Acceleration sensor open detection Error or Normal Normal Error: Momentary interruption
Steering Open Steering angle sensor open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRAC > Data List
Tester Display
EFI Communication Open
Yaw Rate Open
Deceleration Open
Steering Open
50003 105 204,205,206,207
HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
There is a constant open circuit
There are no momentary interruptions
There are momentary interruptions



There is a constant open circuit

2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED

There are no momentary interruptions

3.RECONFIRM DTC

There are momentary interruptions

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH SENSOR AND ECM CONNECTOR IS SECURELY CONNECTED
a.

Turn the ignition switch off.


b.

Check if each sensor or ECM connector is securely connected.

OK:

Each connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Record the output DTCs (for VSC system and/or CAN communication system).

for VSC system: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

for CAN communication system: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for VSC system) after the CAN communication system returns to normal.


Result:
Result Proceed to
DTC (relating to CAN communication system) is output A
DTC (relating to VSC system) is output B
DTC is not output C




A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


d.

Check that there is no momentary interruption.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the ignition switch off.



Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105
c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


e.

Check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

The CAN communication system must be normal when repairing each sensor DTC (for VSC system).


Result:
Result Proceed to
DTC is not output A
DTC is output (relating to VSC system) B
DTC is output (relating to CAN communication system) C



A

END

B

C