Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  CALIBRATION  


DESCRIPTION


a.

After replacing any VSC related components or performing wheel alignment adjustment, clear and read the sensor calibration data.

Refer to the table below and then perform the necessary operation according to the part to be replaced in order to perform calibration.

Parts to be Replaced / Operation Necessary Operation
Skid control ECU (brake actuator assembly) Yaw rate and acceleration sensor zero point calibration.
Yaw rate and acceleration sensor (airbag sensor assembly)
1.

Clearing zero point calibration data.

2.

Yaw rate and acceleration sensor zero point calibration.


Wheel alignment adjustment
1.

Clearing zero point calibration data.

2.

Yaw rate and acceleration sensor zero point calibration.





OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR (When Using Techstream)


NOTICE:
·

Stored system information cannot be overwritten unless it is cleared. Clear the stored information and then store new system information.

·

While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).

·

Be sure to perform this procedure on a level surface (with an inclination of less than 1 degree).



a.

Clear the zero point calibration data.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in P and apply the parking brake.


iv.

Connect the Techstream to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the Techstream on.


vii.

Select the skid control ECU (brake actuator assembly) to clear the zero point calibration data using the Techstream.

Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Reset Memory.

Chassis > ABS/VSC/TRAC > Utility
Tester Display
Reset Memory
50005 105 1138

viii.

Check that the slip indicator light comes on.


ix.

Turn the ignition switch off.

NOTICE:

If the ignition switch is turned to ON for more than 15 seconds with the shift lever in P after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, the skid control ECU (brake actuator assembly) will store the zero point calibration for the acceleration sensor as not being completed. The skid control ECU (brake actuator assembly) will then also indicate this as a malfunction of the VSC system using the indicator light.




b.

Perform zero point calibration of the yaw rate and acceleration sensor.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in P and apply the parking brake.

NOTICE:

DTCs C1210 (Zero Point Calibration of Yaw Rate Sensor Undone) and C1336 (Zero Point Calibration of Acceleration Sensor Undone) will be stored if the shift lever is not in P.



iv.

Connect the Techstream to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the Techstream on.


vii.

Switch the skid control ECU (brake actuator assembly) to Test Mode using the Techstream.

Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Test Mode.

Chassis > ABS/VSC/TRAC > Utility
Tester Display
Test Mode
50005 105 1166

viii.

After the Test Mode has been entered, keep the vehicle stationary on a level surface for 5 seconds or more.


ix.

Check that the slip indicator light comes on for several seconds and then blinks in the Test Mode pattern.

HINT:
·

If the slip indicator light does not blink, perform zero point calibration again.

·

The zero point calibration is performed only once after the system enters the Test Mode.

·

Calibration cannot be performed again until the stored data is cleared.




x.

Turn the ignition switch off and disconnect the Techstream.




OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR (When Using SST Check Wire)


NOTICE:
·

Stored system information cannot be overwritten unless it is cleared. Clear the stored information and then store new system information.

·

While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).

·

Be sure to perform this procedure on a level surface (with an inclination of less than 1 degree).



a.

Clear the zero point calibration data.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in P and apply the parking brake.


iv.

Turn the ignition switch to ON.


v.

The warning light and indicator light come on for 3 seconds to indicate that the initial check is completed.


vi.
C146309
0.108,0.087 0.413,0.238 0.305,0.151 10 *a 1.63,0.813 1.946,0.3 1.946,0.3 2.07,0.3 false 1.614,1.47 1.303,2.016 1.303,2.016 1.18,2.016 false 2.137,0.207 2.441,0.358 0.305,0.151 10 CG 0.933,1.943 1.238,2.094 0.305,0.151 10 TS
*a Front view of DLC3


Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.

SST
09843-18040  


vii.

Check that the slip indicator light comes on.

NOTICE:

If the ignition switch is turned to ON for more than 15 seconds with the shift lever in P after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, the skid control ECU (brake actuator assembly) will store the zero point calibration for the acceleration sensor as not being completed. The skid control ECU (brake actuator assembly) will then also indicate this as a malfunction of the VSC system using the indicator light.



viii.

Turn the ignition switch off.



b.

Perform zero point calibration of the yaw rate and acceleration sensor.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in P and apply the parking brake.

NOTICE:

DTCs 36 (Zero Point Calibration of Yaw Rate Sensor Undone) and 39 (Zero Point Calibration of Acceleration Sensor Undone) will be recorded if the shift lever is not in P.



iv.
C146309
0.108,0.087 0.413,0.238 0.305,0.151 10 *a 1.63,0.813 1.946,0.3 1.946,0.3 2.07,0.3 false 1.614,1.47 1.303,2.016 1.303,2.016 1.18,2.016 false 2.137,0.207 2.441,0.358 0.305,0.151 10 CG 0.933,1.943 1.238,2.094 0.305,0.151 10 TS
*a Front view of DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.


v.

Turn the ignition switch to ON.


vi.

After Test Mode has been entered, keep the vehicle stationary on a level surface for 5 seconds or more.


vii.

Check that the slip indicator light comes on for several seconds and then blinks in the Test Mode pattern.

HINT:
·

If the slip indicator light does not blink, perform zero point calibration again.

·

The zero point calibration is performed only once after the system enters the Test Mode.

·

Calibration cannot be performed again until the stored data is cleared.




viii.

Turn the ignition switch off and disconnect SST from the DLC3.