Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C160258
0.441,0.3 0.653,0.503 0.212,0.203 10 *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
- -


Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU ground
2 (STP) Stop light switch input
3 - (Not used)
4 (RL-) Rear wheel speed LH (-) signal input
5 (RL+) Rear wheel speed LH (+) power supply output
6 (FR-) Front wheel speed RH (-) signal input
7 (FR+) Front wheel speed RH (+) power supply output
8 - (Not used)
9 - (Not used)
10 - (Not used)
11 (SP1) Speed signal output for speedometer
12 (+BS) Solenoid relay power supply
13 (GND2) Pump motor ground
14 (CANL) CAN communication line L
15 - (Not used)
16 (RR-) Rear wheel speed RH (-) signal input
17 (RR+) Rear wheel speed RH (+) power supply output
18 (FL-) Front wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) power supply output
20 - (Not used)
21 - (Not used)
22 - (Not used)
23 - (Not used)
24 (BM) Motor relay power supply
25 (CANH) CAN communication line H
26 - (Not used)
27 - (Not used)
28 - (Not used)
29 - (Not used)
30 (CSW) VSC OFF switch input
31 - (Not used)
32 - (Not used)
33 - (Not used)
34 (IG1) ECU power supply


TERMINAL INSPECTION


a.

Disconnect the A64 connector and measure the voltage or resistance on the wire harness side.

C160261
3.406,0.656 3.75,0.865 0.344,0.208 0.563,0.396 0.875,0.594 0.313,0.198 10 *a 3.469,0.677 3.938,0.917 0.469,0.24 10 A64
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A64-1 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
A64-2 (STP) - Body ground L - Body ground Stop light switch input Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A64-12 (+BS) - Body ground W - Body ground Solenoid relay power supply Always 11 to 14 V
A64-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A64-24 (BM) - Body ground B - Body ground Motor relay power supply Always 11 to 14 V
A64-25 (CANH) - A64-14 (CANL) L*1, R*2 - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A64-30 (CSW) - Body ground L - Body ground VSC OFF switch input VSC OFF switch held ON → OFF (Not pressed) Below 1 Ω → 10 kΩ or higher
A64-34 (IG1) - Body ground L - Body ground ECU power supply Ignition switch ON 11 to 14 V

*1: for 4WD, Manual Air Conditioning System, w/ Tire Pressure Warning System, w/o Intuitive Parking Assist System and w/o Rear View Monitor System

*2: except for 4WD, Manual Air Conditioning System, w/ Tire Pressure Warning System, w/o Intuitive Parking Assist System and w/o Rear View Monitor System