Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM30B0U _54 Brake _010842 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0058073 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Whenever a DTC is detected, the skid control ECU (brake actuator assembly) stores the current vehicle (sensor) state as Freeze Frame Data.


b.

The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.

HINT:
·

However, if the vehicle is stopped or at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU (brake actuator assembly) will stop counting the number of times the ignition switch has been turned from off to ON.

·

Freeze Frame Data at the time the ABS operates: The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS system operates. When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.

·

Freeze Frame Data at the time a DTC is detected: When the skid control ECU (brake actuator assembly) stores data at the time a DTC is detected, no updates will be performed until the data is cleared.





CHECK FREEZE FRAME DATA


a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105

f.

Select a DTC to display its Freeze Frame Data.

Chassis > ABS/VSC/TRAC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Elapsed Time after Freeze Trigger Elapsed time after freeze trigger Min.: 0 msec
Max.: 500 msec
- -
Number of IG ON Number of operations of ignition switch being turned to ON after storing Freeze Frame Data 0 to 31 - -
Buzzer Meter buzzer ON or OFF ON: Buzzer ON
OFF: Buzzer OFF
-
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Gear Position Gear position information Fail, 1st-7th, "P, N", 8th, R or Not R Actual gear position -
Shift Lever Position Shift lever position information Fail, 1st-5th, 6th/B, D/M, "P, N" or R Actual shift lever position -
Operated System Operated system status Non, ABS, VSC, TRAC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC or Sys Actual operated system Non: No operation activated
ABS: ABS activated
VSC: VSC activated
TRAC: TRAC activated
BA: BA activated
Fail: Fail safe mode activated
Sys: System prohibit activated
Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0 V
Max.: 5 V
0.3 to 0.9 V: When brake pedal is released Reading increases when brake pedal is depressed.
M/C Sensor Grade Master cylinder pressure sensor change Min.: -30 MPa/s
Max.: 225 MPa/s
0 MPa/s: When brake pedal is released or pedal held at constant position When brake pedal is being operated: Changes in proportion with pedal movement speed
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s
Max.: 127°/s
0°/s: Vehicle stopped
-128 to 0°/s: Turning right
0 to 127°/s: Turning left
-
Lateral G Lateral G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During turning: Changes in proportion with acceleration
Forward and Rearward G Forward and backward G Min.: -25.10 m/s2
Max.: 24.90 m/s2
- During acceleration/deceleration: Changes in proportion with acceleration
FR Wheel Speed FR wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed FL wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed RR wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed RL wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle acceleration Min.: -25.10 m/s2
Max.: 24.90 m/s2
Vehicle stopped: 0 m/s2 During driving: Changes in proportion with vehicle acceleration/deceleration
Real Engine Torque Real engine torque Min.: -1024 Nm
Max.: 1023 Nm
- -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0%
Max.: 127%
Accelerator pedal released: 0% During accelerator pedal operation: Changes in proportion with the pedal movement
Inspection Mode Inspection mode Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Steering Angle Sensor Steering angle sensor Min.: -3276.8°
Max.: 3276.7°
Turning left: Increases
Turning right: Decreases
-
TRAC/VSC Off Mode TRAC/VSC off mode Normal, TRAC OFF or VSC OFF Normal: Normal mode
TRAC OFF: TRAC off mode
VSC OFF: VSC off mode
-


CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTC will also clear the Freeze Frame Data.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTC and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105