Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM30B0U _55 Steering _010966 STEERING GEAR / LINKAGE _0058245 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL NO. 2 STEERING RACK BOOT

a.
C280229
1.385,1.667 1.844,1.49 false 1.208,1.594 1.521,1.75 0.313,0.156 10 *1 2.281,1.042 2.594,1.198 0.313,0.156 10 *a
*1 Steering Rack End
*a Grease Application Area


Apply lithium soap base glycol grease to the inside of the steering rack end.


b.

Install the No. 2 steering rack boot to the groove on the rack housing.

NOTICE:
·

Be careful not to damage or twist the boot.

·

Make sure that the boot is free of rust and foreign matter.




Hide 2.INSTALL NO. 1 STEERING RACK BOOT

HINT:

Use the same procedure as for the No. 2 steering rack boot.


Hide 3.TIGHTEN NO. 2 STEERING RACK BOOT CLAMP

a.
C280227
1.063,0.323 1.979,0.938 true 1.313,0.031 1.625,0.188 0.313,0.156 10 *a 3.042,1.771 3.354,1.927 0.313,0.156 10 *b 0.781,0.219 1.146,0.375 0.365,0.156 10 SST
*a Hold
*b Turn


Using SST, tighten a new No. 2 steering rack boot clamp as shown in the illustration.

SST
09616-00011  

Clearance:

3.0 mm (0.118 in.) or less


NOTICE:

Be careful not to damage or twist the boot.



Hide 4.TIGHTEN NO. 1 STEERING RACK BOOT CLAMP

HINT:

Use the same procedure as for the No. 2 steering rack boot clamp.


Hide 5.INSTALL STEERING RACK BOOT CLIP

a.

Using pliers, install the 2 boot clips.


Hide 6.INSPECT STEERING GEAR ASSEMBLY

a.
C213399
1.672,0.357 1.967,0.521 0.295,0.164 10 SST 2.433,0.69 2.182,0.439 2.182,0.439 2.021,0.439 false

Using SST, rotate the pinion shaft to see if both the left and right steering rack boots expand and contract smoothly.

SST
09616-00011  

HINT:

If the result is not as specified, use a new steering rack boot clamp and reinstall the steering rack boots.



Hide 7.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.
C150341
1.668,1.564 1.899,1.73 0.23,0.166 10 *a 1.172,1.141 1.172,1.654 1.172,1.654 1.663,1.654 false 1.379,1.146 1.379,1.654 false
*a Matchmark


Install the lock nut and tie rod end to the steering gear assembly so that the matchmarks align.

HINT:

After adjusting toe-in, tighten the lock nut to the specified torque.



Hide 8.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 9.CHECK TIE ROD END SUB-ASSEMBLY

a.
C275665
0.323,0.146 0.635,0.302 0.313,0.156 10 *A 0.333,1.885 0.646,2.042 0.313,0.156 10 *B 2.052,1.573 2.365,1.729 0.313,0.156 10 A 1.292,3.052 1.604,3.208 0.313,0.156 10 B
*A for LH Side
*B for RH Side


Adjust the tie rod end sub-assembly LH and RH so that distance A and distance B are within the specified ranges.

Reference Values:
Tire size Dimension Standard Range
225/65R17 A 76.4 to 78.4 mm (3.008 to 3.086 in.)
B 76.4 to 78.4 mm (3.008 to 3.086 in.)
235/55R18 A 80.1 to 82.1 mm (3.154 to 3.232 in.)
B 80.1 to 82.1 mm (3.154 to 3.232 in.)


HINT:
·

The values listed above are reference values.

·

The toe-in is adjusted in a later step.