Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM30B0U _55 Steering _010850 STEERING COLUMN _0058246 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING OFF CENTER ADJUSTMENT

HINT:

This is the adjustment procedure for when the steering is off-center.


a.

Check if the steering wheel is off-center.

i.
C275666
0.969,1.083 1.667,1.135 true 0.792,0.323 1.156,0.219 true 0.885,0.76 0.979,0.635 0.979,0.635 1.708,0.635 true 0.854,0.927 1.063,0.646 true 1.76,0.563 2.073,0.719 0.313,0.156 10 *a 1.208,0.125 1.521,0.281 0.313,0.156 10 *1 1.719,1.073 2.031,1.229 0.313,0.156 10 *2
*1 Steering Wheel
*2 Steering Column Upper Cover
*a Masking Tape


Apply masking tape to the top center of the steering wheel and steering column upper cover.


ii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph) and hold the steering wheel to maintain the course.


iii.
C275667
1.01,0.5 1.375,0.188 true 1.083,0.969 1.458,1.188 true 0.885,0.792 1.146,0.615 1.146,0.615 1.469,0.615 true 0.885,0.896 1.219,0.625 true 1.51,0.542 1.823,0.698 0.313,0.156 10 *a 1.49,1.135 1.802,1.292 0.313,0.156 10 *1 1.385,0.115 1.698,0.271 0.313,0.156 10 *2
*1 Steering Wheel
*2 Steering Column Upper Cover
*a Marked Line


Draw a line on the masking tape as shown in the illustration.


iv.

Turn the steering wheel to the center position.

HINT:

Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.



v.
C275668
1.031,0.385 1.479,0.188 true 1.271,0.958 1.719,0.76 true 0.896,0.708 1.146,0.51 1.146,0.51 1.563,0.51 true 0.885,0.823 1.385,0.521 true 1.625,0.427 1.938,0.583 0.313,0.156 10 false *a 1.76,0.677 2.073,0.833 0.313,0.156 10 false *1 1.51,0.115 1.823,0.271 0.313,0.156 10 false *2
*1 Steering Wheel
*2 Steering Column Upper Cover
*a Marked Line


Draw a new line on the masking tape on the steering wheel as shown in the illustration.


vi.

Measure the distance between the 2 lines on the masking tape on the steering wheel.


vii.

Convert the measured distance to a steering angle value.

HINT:
·

Measured distance 1 mm (0.0394 in.) = Steering angle of approximately 1°.


·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C170785
1.292,0.833 1.75,0.198 true 1.198,0.792 1.677,0.208 1.677,0.208 1.833,0.208 true 1.917,0.115 2.167,0.292 0.25,0.177 10 false *a
*a Matchmark


Place matchmarks on the RH and LH tie rod ends and rack ends respectively where they can be easily seen.


ii.

Using a paper gauge, measure the distance from the RH and LH tie rod ends to the rack end screws.

HINT:
·

Measure both the RH and LH sides.


·

Make a note of the measured values.




iii.
C145857

Remove the RH and LH boot clips from the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle value.

HINT:

One 360° turn of a rack end (1.5 mm (0.0591 in.) horizontal movement) is equal to a 12° change in steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Make sure that the difference in length between the RH and LH tie rod ends and rack end screws is within 1.5 mm (0.0591 in.).



vii.

Install the RH and LH boot clips.