Home › Steering › STEERING COLUMN › STEERING PAD SWITCH
RM30B0U _55 Steering _010850 STEERING COLUMN _0058249 STEERING PAD SWITCH G

STEERING COLUMN  STEERING PAD SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT STEERING PAD SWITCH ASSEMBLY

a.

Inspect the pad switch.

i.

Measure the resistance according to the value(s) in the table below.

C280260
6.073,0.583 6.521,0.833 0.448,0.25 2.635,0.542 3.083,0.792 0.448,0.25 2.771,1.979 2.75,1.385 true 2.5,2.031 2.292,1.865 true 2.49,2.26 2.208,2.26 true 2.646,2.104 2.438,1.521 true 2.802,2.094 3,1.583 3,1.583 3.167,1.583 true 2.344,2.708 2.542,2.51 true 2.646,2.938 2.802,2.521 true 4.781,2.01 4.99,1.719 true 4.906,2.125 5.219,2.125 true 4.76,2.26 5.104,2.625 true 4.76,2.542 4.969,2.865 true 2.917,2.135 3.167,2.302 3.167,2.302 3.333,2.302 true 2.792,2.26 3,2.5 3,2.5 3.167,2.5 true 4.885,0.646 4.667,0.531 true 5.49,1.115 5.271,0.833 true 4.99,0.625 4.792,0.365 true 5.271,0.635 5.49,0.375 true 4.781,1.115 4.99,0.823 true 4.99,1.198 5.094,0.833 true 5.313,1.188 5.167,0.833 true 5.083,0.615 4.969,0.198 true 2.135,1.729 2.448,1.885 0.313,0.156 10 false *1 2.052,2.188 2.365,2.344 0.313,0.156 10 false *2 2.344,1.354 2.656,1.51 0.313,0.156 10 false *3 3.396,2.229 3.708,2.385 0.313,0.156 10 false *4 2.677,1.219 2.99,1.375 0.313,0.156 10 false *5 3.208,2.427 3.521,2.583 0.313,0.156 10 false *6 3.219,1.51 3.531,1.667 0.313,0.156 10 false *7 2.198,2.667 2.51,2.823 0.313,0.156 10 false *8 2.531,2.938 2.844,3.094 0.313,0.156 10 false *9 5.281,2.052 5.75,2.208 0.469,0.156 10 false *10 5.021,1.563 5.49,1.719 0.469,0.156 10 false *11 5.146,2.625 5.615,2.781 0.469,0.156 10 false *12 4.906,2.906 5.375,3.063 0.469,0.156 10 false *13 0.688,0.469 1,0.625 0.313,0.156 10 false *a 6.24,0.615 6.396,0.813 0.156,0.198 10 false A 2.813,0.594 2.969,0.792 0.156,0.198 10 false B 5.5,1.104 5.906,1.302 0.406,0.198 10 false AU1 5.229,1.24 5.635,1.438 0.406,0.198 10 false AU2 4.802,1.24 5.208,1.438 0.406,0.198 10 false AU3 4.5,1.104 4.906,1.302 0.406,0.198 10 false EAU 4.76,0.031 5.167,0.229 0.406,0.198 10 false -DP 4.51,0.229 4.917,0.427 0.406,0.198 10 false +DP 5.469,0.229 5.875,0.427 0.406,0.198 10 false IL+2 4.448,0.448 4.854,0.646 0.406,0.198 10 false HO 3.167,0.792 3.406,0.979 0.24,0.188 10 false HO
*1 Volume+ Switch *2 Volume- Switch
*3 Left Switch *4 Right Switch
*5 Right Switch *6 Down Switch
*7 ENTER Switch *8 Mode Switch
*9 Back Switch *10 with Voice Switch
*11 Off Hook Switch *12 On Hook Switch
*13 DISP Switch - -
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A11 (AU1) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Volume+ is pushed 950 to 1050 Ω
Volume- is pushed 2954 to 3265 Ω
Up switch is pushed Below 2.5 Ω
Down switch is pushed 312 to 345 Ω
A9 (AU3) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Left switch is pushed 2954 to 3265 Ω
Right switch is pushed 950 to 1050 Ω
ENTER Switch is pushed Below 2.5 Ω
Back Switch is pushed 312 to 345 Ω
A10 (AU2) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Mode switch is pushed Below 2.5 Ω
On Hook switch is pushed 312 to 345 Ω
Off Hook switch is pushed 950 to 1050 Ω
Voice switch is pushed *10 2954 to 3265 Ω
A2 (+DP) - A3 (-DP) DISP switch is pushed Below 2.5 Ω
A1 (HO) - B (HO) Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.


ii.

Connect the battery positive (+) lead to terminal A5 (IL+2) and the negative (-) lead to terminal A8 (EAU) of the steering pad switch assembly connector.


iii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering pad switch assembly.



b.

Inspect the pad switch.

i.

Measure the resistance according to the value(s) in the table below.

C294323
2.51,0.542 3.01,0.792 0.5,0.25 5.583,0.583 6.083,0.833 0.5,0.25 2.219,2.927 2.635,2.51 true 2.073,2.125 2.573,2.125 true 4.792,2 5.208,1.583 true 2.833,2.083 3,1.667 true 4.833,2.25 5.417,2.25 true 4.76,2.542 5.177,2.875 true 2.229,1.771 2.677,1.99 true 4.479,0.51 4.875,0.646 true 2.25,2.5 2.667,2.25 true 4.833,0.177 5.083,0.625 true 4.677,0.333 5,0.635 true 5.677,0.292 5.26,0.625 true 5.271,0.823 5.594,1.031 true 5.177,0.833 5.469,1.208 true 4.781,1.063 4.99,0.833 true 2.073,1.656 2.385,1.813 0.313,0.156 10 false *1 2.094,2.448 2.406,2.604 0.313,0.156 10 false *2 2.979,1.521 3.292,1.677 0.313,0.156 10 false *3 1.917,2.052 2.229,2.208 0.313,0.156 10 false *4 2.063,2.917 2.375,3.073 0.313,0.156 10 false *5 5.25,1.469 5.563,1.625 0.313,0.156 10 false *6 5.458,2.167 5.771,2.323 0.313,0.156 10 false *7 5.208,2.865 5.521,3.021 0.313,0.156 10 false *8 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 5.479,1.188 5.792,1.344 0.313,0.156 10 false AU2 5.615,0.99 5.927,1.146 0.313,0.156 10 false AU1 4.469,1.031 4.781,1.188 0.313,0.156 10 false EAU 4.188,0.417 4.5,0.573 0.313,0.156 10 false IL+2 4.385,0.208 4.698,0.365 0.313,0.156 10 false +DP 4.615,0.031 4.927,0.188 0.313,0.156 10 false -DP 5.708,0.198 6.021,0.354 0.313,0.156 10 false HO 3.208,0.833 3.521,0.99 0.313,0.156 10 false HO 2.729,0.594 3.042,0.75 0.313,0.156 10 false B 5.771,0.625 6.083,0.781 0.313,0.156 10 false A
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 Mode Switch *6 Off Hook Switch
*7 On Hook Switch *8 DISP Switch
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A11 (AU1) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Volume+ is pushed 950 to 1050 Ω
Volume- is pushed 2954 to 3265 Ω
Seek+ switch is pushed Below 2.5 Ω
Seek- switch is pushed 312 to 345 Ω
A10 (AU2) - A8 (EAU) No switch is pushed 95 to 105 kΩ
Mode switch is pushed Below 2.5 Ω
On Hook switch is pushed 312 to 345 Ω
Off Hook switch is pushed 950 to 1050 Ω
Voice switch is pushed 2954 to 3265 Ω
A2 (+DP) - A3 (-DP) DISP switch is pushed Below 2.5 Ω
A5 (HO) - B (HO) Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.


ii.

Connect the battery positive (+) lead to terminal A1 (IL+2) and the negative (-) lead to terminal A8 (EAU) of the steering pad switch assembly connector.


iii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering pad switch assembly.