Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM30B0U _58 Vehicle Interior _009874 DOOR LOCK _0058010 POWER DOOR LOCK CONTROL SYSTEM Y

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the power door lock control system.

·

*: Use the Techstream.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS CHECK
2.CUSTOMER PROBLEM ANALYSIS CHECK
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:



What Vehicle model, system name
When Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where Whether the problem occurs at a specific location
Under what conditions? Whether the doors were locked or unlocked, whether the ignition switch was ON, whether the engine has started
How did it happen? Problem symptoms

Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Using the Techstream, check for CAN communication system DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Proceed to
CAN DTCs are not output
CAN DTCs are output



CAN DTCs are not output

5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

CAN DTCs are output

5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the Techstream, check for LIN communication system DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR


Result:
Proceed to
LIN DTCs are not output
LIN DTCs are output



LIN DTCs are not output

6.CHECK FOR DTC (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)*

LIN DTCs are output

6.CHECK FOR DTC (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)*
a.

Clear the DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > Master Switch > Clear DTCs
50002 148

b.

Recheck for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR

Body Electrical > Master Switch > Trouble Codes
50001 148

Result:
Proceed to
DTC B2312 is not output
DTC B2312 is output



DTC B2312 is not output

7.PROBLEM SYMPTOMS TABLE

DTC B2312 is output

7.PROBLEM SYMPTOMS TABLE

Result:
Proceed to
Fault is not listed in Problem Symptoms Table
Fault is listed in Problem Symptoms Table



Fault is not listed in Problem Symptoms Table

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

Fault is listed in Problem Symptoms Table

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END