Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR MAIN SWITCH
RM30B0U _56 Audio / Visual / Telematics _009404 PARK ASSIST / MONITORING _0058393 BLIND SPOT MONITOR MAIN SWITCH G

PARK ASSIST / MONITORING  BLIND SPOT MONITOR MAIN SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCELING SWITCH ASSEMBLY)

a.
E224422
1.958,1.333 2.542,0.625 false 1.5,1.458 1.854,1.948 1.854,1.948 1.958,1.948 false 1.948,1.344 2.531,0.635 false 2.573,0.521 2.698,0.677 0.125,0.156 10 D 2.01,1.854 2.135,2.01 0.125,0.156 10 B 0.167,0.146 0.344,0.302 0.177,0.156 10 *a
*a Component without harness connected
(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
11 (B) - 8 (D) Blind spot monitor main switch assembly on (not protruding) Below 1 Ω
11 (B) - 8 (D) Blind spot monitor main switch assembly off (protruding) 10 kΩ or higher


If the result is not as specified, replace the blind spot monitor main switch (warning canceling switch assembly).


b.

Check that the switch illuminates.

i.
E224422
1.802,1.479 2.167,1.969 2.167,1.969 2.271,1.969 false 1.646,1.479 1.354,1.969 1.354,1.969 1.271,1.969 false 2.333,1.885 2.688,2.042 0.354,0.156 10 ILL- 0.167,0.146 0.344,0.302 0.177,0.156 10 *a 0.948,1.875 1.26,2.031 0.313,0.156 10 ILL+
*a Component without harness connected
(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))


Apply battery voltage to the blind spot monitor main switch (warning canceling switch assembly) and check that the switch illuminates.

OK:
Connection Specified Condition
Battery positive (+) → Terminal 10 (ILL+)
Battery negative (-) → Terminal 9 (ILL-)
Illuminates


If the result is not as specified, replace the blind spot monitor main switch (warning canceling switch assembly).



c.

Check that the switch indicator illuminates.

i.
E224422
1.26,1.406 0.635,1.354 false 1.49,1.469 1.844,1.958 1.844,1.958 1.948,1.958 false 0.521,1.292 0.646,1.448 0.125,0.156 10 E 2.01,1.885 2.135,2.042 0.125,0.156 10 B 0.167,0.146 0.344,0.302 0.177,0.156 10 *a
*a Component without harness connected
(Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly))


Apply battery voltage to the blind spot monitor main switch assembly and check operation of the switch as shown in the table below.

OK:
Connection Switch Condition Specified Condition
Battery positive (+) → Terminal 11 (B)
Battery negative (-) → Terminal 12 (E)
Blind spot monitor main switch assembly on (not protruding) Indicator Illuminates


If the result is not as specified, replace the back sonar or blind spot monitor main switch (warning canceling switch assembly).