Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM30B0U _59 Vehicle Exterior _010075 WIPER / WASHER _0058467 WIPER AND WASHER SYSTEM D

WIPER / WASHER  WIPER AND WASHER SYSTEM  SYSTEM DESCRIPTION  


WASHER-LINKED OPERATION


a.

This system operates the front wipers at low speed immediately after spraying a jet of washer fluid when the front washer switch is turned on for 0.3 seconds or more.

The system operates the front wipers at low speed for approximately 2.2 seconds and then stops operation when the washer switch is turned on for 1.5 seconds or more.



FRONT WIPER INTERMITTENT OPERATION (w/ Intermittent Timing)


a.

The system operates the front wipers once in approximately 1.6 to 10.7 seconds when the windshield wiper switch asse,bly is turned to the INT position. The intermittent time can be adjusted from 1.6 to 10.7 seconds by using the intermittent time adjust dial.


b.

If the front wiper switch is turned to the INT position, current flows from the already charged capacitor C1 through terminals INT1 and INT2 of the front wiper switch to Tr1 (transistor). When Tr1 turns on, current flows from terminal +S of the front wiper switch to terminal +1 of the front wiper switch, to terminal +1 of the wiper motor, to the wiper motor and finally to ground, causing the wiper motor to operate. At the same time, current flows from capacitor C1 to terminal INT1 of the front wiper switch and then INT2. When the current flow from capacitor C1 ends, Tr1 turns off to turn off the relay contact and halt the wiper motor.

E274269
0.042,0.01 4.938,0.208 4.896,0.198 10 false Windshield Wiper Switch Assembly 3.125,0.396 5.875,0.594 2.75,0.198 10 false Front Wiper Switch 0.198,3.313 3.104,3.51 2.906,0.198 10 false Front Washer Switch 0.667,0.521 3.573,0.719 2.906,0.198 10 false Intermittent Timing Switch*1 3.594,0.792 3.906,0.99 0.313,0.198 10 false +B 3.969,0.792 4.281,0.99 0.313,0.198 10 false +2 4.313,0.781 4.625,0.979 0.313,0.198 10 false +1 4.698,0.781 5.01,0.979 0.313,0.198 10 false +S 5.771,0.781 6.271,1.042 0.5,0.26 10 false B1 5.385,0.792 5.885,1.052 0.5,0.26 10 false INT2 5.021,0.792 5.521,1.052 0.5,0.26 10 false INT1 3.198,0.969 3.813,1.167 0.615,0.198 10 false Mist 3.24,1.156 3.698,1.354 0.458,0.198 10 false Off 3.25,1.323 3.938,1.49 0.688,0.167 10 false Int 1.115,0.969 1.271,1.167 0.156,0.198 10 false F 1.479,0.958 1.635,1.156 0.156,0.198 10 false A 1.844,0.958 2,1.156 0.156,0.198 10 false B 2.094,0.969 2.552,1.219 0.458,0.25 10 false COM 0.719,1.156 1.031,1.354 0.313,0.198 10 false P1 0.719,1.333 1.031,1.531 0.313,0.198 10 false P2 0.719,1.51 1.031,1.708 0.313,0.198 10 false P3 0.708,1.708 1.021,1.906 0.313,0.198 10 false P4 3.208,1.5 3.667,1.698 0.458,0.198 10 false Low 0.323,4.083 0.781,4.281 0.458,0.198 10 false Off 0.313,3.885 0.625,4.083 0.313,0.198 10 false On 0.656,3.708 1.115,3.906 0.458,0.198 10 false +B2 1.031,3.708 1.344,3.906 0.313,0.198 10 false WR 1.406,3.698 1.719,3.896 0.313,0.198 10 false WF 1.771,3.698 2.083,3.896 0.313,0.198 10 false EW 4.979,5.698 6.583,6.104 1.604,0.406 10 false Windshield Washer Motor and Pump Assembly 6.865,5.25 7.146,5.49 0.281,0.24 10 false WF 6.188,6.688 7.156,7.229 0.969,0.542 10 false from IG1 NO. 2 Relay 5.26,7.385 5.719,7.583 0.458,0.198 10 false WSH 5.167,6.844 6.083,7.042 0.917,0.198 10 false WIP FR 2.365,8.375 7.156,8.594 4.792,0.219 10 false Windshield Wiper Motor Assembly 0.771,5.25 1.229,5.448 0.458,0.198 10 false +B2 1.188,5.25 1.5,5.448 0.313,0.198 10 false WR 1.906,5.26 2.219,5.458 0.313,0.198 10 false EW 4.375,5.24 4.688,5.438 0.313,0.198 10 false +S 3.646,5.26 3.958,5.458 0.313,0.198 10 false +1 2.938,5.26 3.25,5.458 0.313,0.198 10 false +2 3.208,1.698 3.667,1.896 0.458,0.198 10 false High 2.25,1.896 2.563,2.094 0.313,0.198 10 false *1 1.927,1.896 2.24,2.094 0.313,0.198 10 false *1 1.542,1.906 1.854,2.104 0.313,0.198 10 false *1 1.198,1.906 1.51,2.104 0.313,0.198 10 false *1 3.344,4.063 3.656,4.26 0.313,0.198 10 false *1 3.792,3.958 4.104,4.156 0.313,0.198 10 false *1 4.302,4.406 4.615,4.604 0.313,0.198 10 false *2 4.313,3.99 4.625,4.188 0.313,0.198 10 false *1 4.896,3.969 5.208,4.167 0.313,0.198 10 false *1 3.896,4.594 4.208,4.792 0.313,0.198 10 false C1 5.563,4.156 5.875,4.354 0.313,0.198 10 false Tr1 6.292,3.458 6.604,3.656 0.313,0.198 10 false Tr2 6.49,4.188 6.802,4.385 0.313,0.198 10 false C2 3.896,6.771 4.208,6.969 0.313,0.198 10 false +B 2.917,6.75 3.229,6.948 0.313,0.198 10 false +2 3.583,6.76 3.896,6.958 0.313,0.198 10 false +1 2.26,8.156 2.573,8.354 0.313,0.198 10 false E 4.333,6.76 4.646,6.958 0.313,0.198 10 false +S 2.375,5.271 2.688,5.469 0.313,0.198 10 false +B 0.063,8.01 4.042,8.208 3.979,0.198 10 false *1: w/ Intermittent Timing 0.063,8.417 4.042,8.615 3.979,0.198 10 false *2: w/o Intermittent Timing 6.219,2.323 6.969,2.688 0.75,0.365 10 false Front Wiper Relay

When the relay contact turns off, capacitor C1 begins to charge again and Tr1 remains off until charging has been completed. This period corresponds to the intermittent time. When capacitor C1 is fully charged, Tr1 turns on and then the relay contact turns on, causing the motor to operate again. This cycle is the intermittent operation.The intermittent time can be adjusted by using the intermittent time adjust dial (variable resistor) to change the charge time of capacitor C1.



REAR WIPER INTERMITTENT OPERATION


a.

When the rear wiper switch is turned to the INT position, current flows from the capacitor of the intermittent operation control circuit to turn on the transistor. Current flows from terminal +B of the rear wiper relay to the relay coil, to the transistor, to terminal C1 of the rear wiper relay, to terminal C1R of the rear wiper switch and finally to ground, causing the relay contact point to turn on.

E274270
2.979,7.24 6.802,7.438 3.823,0.198 10 false Rear Wiper Motor Assembly 3.542,2.958 6.146,3.156 2.604,0.198 10 false Rear Wiper Switch 3.5,3.406 6.25,3.604 2.75,0.198 10 false Rear Washer Switch 4.917,2.667 5.229,2.865 0.313,0.198 10 false WR 5.25,2.667 5.708,2.865 0.458,0.198 10 false +1R 5.615,2.667 6.073,2.865 0.458,0.198 10 false C1R 6.021,2.656 6.333,2.854 0.313,0.198 10 false EW 6.344,2.656 6.802,2.854 0.458,0.198 10 false +B2 6.729,2.656 7.042,2.854 0.313,0.198 10 false WF 3.896,1.677 5.5,2.052 1.604,0.375 10 false Windshield Washer Motor and Pump Assembly 4.583,0.635 5.5,0.833 0.917,0.198 10 false WIP RR 5.802,0.896 7.125,1.302 1.323,0.406 10 false from IG1 NO.2 Relay 4.688,1.052 5.146,1.25 0.458,0.198 10 false WSH 3.344,3.781 4.896,4.135 1.552,0.354 10 false Windshield Wiper Switch Assembly 0.573,4.469 4.396,4.667 3.823,0.198 10 false Rear Wiper Motor Assembly 0.344,0.177 0.5,0.375 0.156,0.198 10 false E 2.792,1.406 3.021,1.656 0.229,0.25 10 false +B 2.792,2.594 3.104,2.792 0.313,0.198 10 false LS 2.802,2.802 3.115,3 0.313,0.198 10 false C1 2.833,3.052 3.146,3.25 0.313,0.198 10 false W 2.188,1.646 2.5,1.844 0.313,0.198 10 false LM 2.177,1.854 2.49,2.052 0.313,0.198 10 false SM 2.208,1.438 2.438,1.688 0.229,0.25 10 false +B 1.74,0.344 5.563,0.542 3.823,0.198 10 false Rear Wiper Motor 0.844,4.01 4.667,4.208 3.823,0.198 10 false Rear Wiper Relay 1.51,0.833 1.74,1.083 0.229,0.25 10 false +1 1.208,0.833 1.438,1.083 0.229,0.25 10 false +B 1.01,0.833 1.24,1.083 0.229,0.25 10 false S

When the relay contact turns on, current flows from terminal +B of the rear wiper relay to the relay contact, to terminal LM of the rear wiper relay, to terminal +1 of the rear wiper motor, to the rear wiper motor and finally to ground, causing the rear wiper motor to operate. The transistor turns off immediately after the rear wiper motor operation as the current flow from the capacitor ends, causing the relay contact to turn off.

Even when the relay contact turns off, current flows from terminal +B of the rear wiper motor to the relay contact in the rear wiper motor, to terminal S of the rear wiper motor, to terminal SM of the rear wiper relay, to the contact of the rear wiper relay, to terminal LM of the rear wiper relay, to terminal +1 of the rear wiper motor and finally to ground, causing the rear wiper motor to operate, until the rear wiper motor stops at the automatic stop position. The rear wiper motor stops at the automatic stop position as the relay contact in the rear wiper motor turns off.

The capacitor in the intermittent operation control circuit is charged in approximately 12 seconds after the current flow ends. After the charge is completed, current starts flowing again to turn on the transistor, causing the relay contact to turn on.

This cycle of current flow and charging described above is the intermittent operation.



WASHER FLUID LEVEL WARNING


a.

When the volume of washer fluid decreases to below a certain level (when the level warning switch is turned on), the combination meter assembly warns the driver through the illumination of the master warning light on the washer warning light.