DATA LIST
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / D-Door Motor or Main Body / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Auto SW | Driver door power window auto switch signal | ON or OFF | ON: Driver door power window auto switch being operated
OFF: Driver door power window auto switch not being operated |
- |
| D Door P/W Up SW | Driver door power window manual up switch signal | ON or OFF | ON: Driver door power window manual up switch being operated
OFF: Driver door power window manual up switch not being operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | ON or OFF | ON: Driver door power window manual down switch being operated
OFF: Driver door power window manual down switch not being operated |
- |
| Glass Position (Close-1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (1/4-2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (2/4-3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (3/4-Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Number of Trouble Codes | Number of trouble codes | Min.: 0 or Max.: 255 | Number of DTCs will be displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Front door courtesy light switch RH | ON or OFF | ON: Front door RH open
OFF: Front door RH closed |
- |
| FL Door Courtesy SW | Front door courtesy light switch LH | ON or OFF | ON: Front door LH open
OFF: Front door LH closed |
- |
| Communication D-Door Motor | Connection status between front power window regulator motor assembly LH and main body ECU (multiplex network body ECU) | OK or STOP | OK: Normal communication
STOP: Communication stopped |
- |
ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / D-Door Motor or Main Body / Active Test.
According to the display on the Techstream, perform the Active Test.
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Driver door power window | OFF, UP or DOWN | - |
Up and down movement does not occur if the arrow is not pressed and held.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| IG OFF P/W Control Permission Output | Power window | OFF or ON | Perform this Active Test with the ignition switch off |
If Active Test is turned on, only the driver side power window does not operate.