Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  B2780  Push Switch / Key Unlock Warning Switch Malfunction  


DESCRIPTION

This DTC is stored if the transponder key ECU assembly does not detect that the unlock warning switch assembly is on even when the ignition switch is ON.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2780 Push Switch / Key Unlock Warning Switch Malfunction The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip detection logic*).
·

Harness or connector

·

Unlock warning switch assembly

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2780 Key SW

WIRING DIAGRAM

B278950
2.167,0.99 4.292,1.344 2.125,0.354 10 Unlock Warning Switch Assembly 2.167,0.823 2.479,1.063 0.313,0.24 10 G7 5.375,1.792 6.813,2.323 1.438,0.531 10 Transponder Key ECU Assembly 5.375,1.635 5.781,1.802 0.406,0.167 10 G88 5.646,0.542 6,0.698 0.354,0.156 10 KSW 5.479,0.469 5.604,0.625 0.125,0.156 10 3 3.74,0.458 3.865,0.615 0.125,0.156 10 1 2.5,0.458 2.625,0.615 0.125,0.156 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2780 is not output
B2780 is output



B2780 is not output

B2780 is output

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the G7 unlock warning switch assembly connector.


b.

Disconnect the G88 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-1 - G88-3 (KSW) Always Below 1 Ω
G7-2 - Body ground Always Below 1 Ω
G7-1 - Body ground Always 10 kΩ or higher
G88-3 (KSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR