Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The antenna coil in the transponder key coil is open/shorted.
·

Harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2784 Antenna Coil Status

WIRING DIAGRAM

B329324
5.469,2.542 5.927,2.74 0.458,0.198 10 G88 5.469,2.698 6.948,3.146 1.479,0.448 10 Transponder Key ECU Assembly 1.292,3.042 1.75,3.24 0.458,0.198 10 G6 1.281,3.188 3.125,3.49 1.844,0.302 10 Transponder Key Coil 2.792,0.76 3.552,1.052 0.76,0.292 10 ANT1 2.781,1.948 3.542,2.24 0.76,0.292 10 ANT2 5.667,0.896 6.427,1.188 0.76,0.292 10 ANT1 5.677,2.063 6.438,2.354 0.76,0.292 10 ANT2 5.51,0.802 5.75,1.042 0.24,0.24 10 4 5.427,1.958 5.667,2.198 0.24,0.24 10 15 3.25,0.75 3.49,0.99 0.24,0.24 10 1 3.229,1.948 3.469,2.188 0.24,0.24 10 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2784 is not output
B2784 is output



B2784 is not output

B2784 is output

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the transponder key coil.


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2784 is not output
B2784 is output



B2784 is not output

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

B2784 is output

6.CHECK TRANSPONDER KEY COIL (OUTPUT)
6.CHECK TRANSPONDER KEY COIL (OUTPUT)
a.

Using an oscilloscope, check the waveform.

B329326
3.417,0.073 3.74,0.292 0.323,0.219 4.115,1.167 3.813,0.792 false 3.177,1.167 3.323,0.771 false 0.115,0.115 0.427,0.313 0.313,0.198 10 *a 1,1.448 1.313,1.646 0.313,0.198 10 *b 1,3.542 1.313,3.74 0.313,0.198 10 *c 6.542,2.479 7.083,2.781 0.542,0.302 10 GND 6.552,4.552 7.094,4.854 0.542,0.302 10 GND 3.979,1.188 4.521,1.49 0.542,0.302 10 ANT1 3.031,1.188 3.573,1.49 0.542,0.302 10 ANT2 3.49,0.094 3.948,0.292 0.458,0.198 10 G6
*a Component with harness connected
(Transponder Key Coil)
*b Waveform 1
*c Waveform 2 - -


Waveform 1
Item Content
Tester Connection G6-1 (ANT1) ←→ Body ground
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Within 3 seconds of inserting key into ignition key cylinder

Waveform 2
Item Content
Tester Connection G6-5 (ANT2) ←→ Body ground
Tool Setting 2 V/DIV., 500 ms/DIV
Tool Setting Within 3 seconds of inserting key into ignition key cylinder

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY ECU>REMOVAL

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2784 is not output
B2784 is output



B2784 is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B2784 is output

10.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the G6 transponder key coil connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-4 (ANT1) - G6-1 (ANT1) Always Below 1 Ω
G88-15 (ANT2) - G6-5 (ANT2) Always Below 1 Ω
G88-4 (ANT1) - Body ground Always 10 kΩ or higher
G6-1 (ANT1) - Body ground Always 10 kΩ or higher
G88-15 (ANT2) - Body ground Always 10 kΩ or higher
G6-5 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR