Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  B2796  No Communication in Immobiliser System  


DESCRIPTION

This DTC is stored when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2796 No Communication in Immobiliser System The key ID code cannot be transmitted to the transponder key ECU assembly (1 trip detection logic*).
·

Key

·

Harness or connector

·

Transponder key coil

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2796 -

WIRING DIAGRAM

B329324
5.469,2.542 5.927,2.74 0.458,0.198 10 G88 5.469,2.698 6.948,3.146 1.479,0.448 10 Transponder Key ECU Assembly 1.292,3.042 1.75,3.24 0.458,0.198 10 G6 1.281,3.188 3.125,3.49 1.844,0.302 10 Transponder Key Coil 2.792,0.76 3.552,1.052 0.76,0.292 10 ANT1 2.781,1.948 3.542,2.24 0.76,0.292 10 ANT2 5.667,0.896 6.427,1.188 0.76,0.292 10 ANT1 5.677,2.063 6.438,2.354 0.76,0.292 10 ANT2 5.51,0.802 5.75,1.042 0.24,0.24 10 4 5.427,1.958 5.667,2.198 0.24,0.24 10 15 3.25,0.75 3.49,0.99 0.24,0.24 10 1 3.229,1.948 3.469,2.188 0.24,0.24 10 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or key is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTCs each time.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2796 is not output
DTC B2796 is output for all of the keys
DTC B2796 is output for any of the keys



B2796 is not output

DTC B2796 is output for all of the keys

3.REPLACE TRANSPONDER KEY ECU ASSEMBLY

DTC B2796 is output for any of the keys

6.REPLACE KEY
3.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY ECU>REMOVAL

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION



Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2796 is not output
B2796 is output



B2796 is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B2796 is output

REPLACE KEY FOR WHICH DTC WAS OUTPUT

6.REPLACE KEY
a.

Replace the key for which the DTC was stored.

NOTICE:

Key ID code registration is necessary when replacing the key.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION



Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B2796 is not output
B2796 is output



B2796 is not output

END (KEY WAS DEFECTIVE)

B2796 is output