Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction One of the following conditions is met:
·

Error in communication between ECM and transponder key ECU assembly.

·

Error in communication lines.

·

Communication ID is different during communication between ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.*1

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2

*1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.

*2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

B341473
2.021,0.344 2.406,0.51 0.385,0.167 10 false 29 2.031,1.104 2.417,1.271 0.385,0.167 10 false 28 1.667,0.469 2.052,0.635 0.385,0.167 10 false IMO 1.708,1.229 2.094,1.396 0.385,0.167 10 false IMI 5.438,0.375 5.667,0.552 0.229,0.177 10 false 12 5.438,1.125 5.667,1.302 0.229,0.177 10 false 13 5.719,0.49 6.104,0.656 0.385,0.167 10 false EFII 5.729,1.24 6.115,1.406 0.385,0.167 10 false EFIO 1.281,1.979 1.948,2.156 0.667,0.177 10 false A62 1.292,2.125 2.156,2.313 0.865,0.188 10 false ECM 5.594,1.99 5.979,2.156 0.385,0.167 10 false G88 5.594,2.156 6.635,2.51 1.042,0.354 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Proceed to
B2799 is not output
DTC B2799 is output
Other DTCs are output



B2799 is not output

DTC B2799 is output

3.REGISTER ECU COMMUNICATION ID

Other DTCs are output

3.REGISTER ECU COMMUNICATION ID

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

5.INSPECT ECM (IMO TERMINAL VOLTAGE)
5.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the A62 ECM connector.


b.

Turn the ignition switch to ON.


c.
B344496
0.198,0.885 0.594,1.115 0.396,0.229 2.188,1.302 2.823,1.677 false 2.74,1.729 3.083,1.896 0.344,0.167 10 false IMO 0.25,0.219 0.563,0.375 0.313,0.156 10 false *a 0.26,0.906 0.573,1.063 0.313,0.156 10 false A62
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
A62-29 (IMO) - Body ground Ignition switch turned to ON using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Proceed to
Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Terminal IMO stuck low (2.4 V or less)

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

Terminal IMO stuck high (12 V) or abnormal waveform

9.REPLACE ECM
6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-12 (EFII) - A62-29 (IMO) Always Below 1 Ω
G88-12 (EFII) - Body ground Always 10 kΩ or higher
A62-29 (IMO) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - A62-28 (IMI) Always Below 1 Ω
G88-13 (EFIO) - Body ground Always 10 kΩ or higher
A62-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY ECU>REMOVAL

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

9.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID

Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG