Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B271007
5.406,2.021 6.802,2.427 1.396,0.406 10 false Transponder Key ECU Assembly 5.385,1.844 5.896,2.042 0.51,0.198 10 false G88 1.167,2.01 1.865,2.198 0.698,0.188 10 false ECM 1.792,0.896 2.344,1.083 0.552,0.188 10 false 28 1.5,1.01 1.958,1.313 0.458,0.302 10 false IMI 1.177,1.833 1.771,2.021 0.594,0.188 10 false A62 5.198,0.906 5.698,1.26 0.5,0.354 10 false 13 5.5,1.021 6.073,1.406 0.573,0.385 10 false EFIO

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B279A is not output
B279A is output



B279A is not output

B279A is output

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-13 (EFIO) - A62-28 (IMI) Always Below 1 Ω
A62-28 (IMI) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY ECU>REMOVAL

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
B279A is not output
B279A is output



B279A is not output

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B279A is output