Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B341473
2.021,0.344 2.406,0.51 0.385,0.167 10 false 29 2.031,1.104 2.417,1.271 0.385,0.167 10 false 28 1.667,0.469 2.052,0.635 0.385,0.167 10 false IMO 1.708,1.229 2.094,1.396 0.385,0.167 10 false IMI 5.438,0.375 5.667,0.552 0.229,0.177 10 false 12 5.438,1.125 5.667,1.302 0.229,0.177 10 false 13 5.719,0.49 6.104,0.656 0.385,0.167 10 false EFII 5.729,1.24 6.115,1.406 0.385,0.167 10 false EFIO 1.281,1.979 1.948,2.156 0.667,0.177 10 false A62 1.292,2.125 2.156,2.313 0.865,0.188 10 false ECM 5.594,1.99 5.979,2.156 0.385,0.167 10 false G88 5.594,2.156 6.635,2.51 1.042,0.354 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 61
Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Proceed to
DTCs are not output
DTCs are output



DTCs are not output

3.READ VALUE USING TECHSTREAM (IMMOBILISER FUEL CUT)

DTCs are output

3.READ VALUE USING TECHSTREAM (IMMOBILISER FUEL CUT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Engine and ECT / Data List.


e.

Read the Data List according to the display on the Techstream.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut OFF/ON - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 61 681
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.


Result:
Proceed to
Engine can be started
Engine cannot be started



Engine can be started

Engine cannot be started

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.


Result:
Proceed to
Engine can be started
Engine cannot be started



Engine can be started

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

Engine cannot be started

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-12 (EFII) - A62-29 (IMO) Always Below 1 Ω
G88-12 (EFII) - Body ground Always 10 kΩ or higher
A62-29 (IMO) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - A62-28 (IMI) Always Below 1 Ω
G88-13 (EFIO) - Body ground Always 10 kΩ or higher
A62-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY ECU>REMOVAL

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.


Result:
Proceed to
Engine can be started
Engine cannot be started



Engine can be started

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

Engine cannot be started