Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  Key Cannot be Registered  


DESCRIPTION

A maximum of 5 master key ID codes and 3 sub key ID codes can be registered.

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.CHECK REGISTRATION MODE
a.

Check that the system enters registration mode.

OK:

System enters registration mode.



Result:
Proceed to
OK
NG



OK

2.CHECK SECURITY INDICATOR LIGHT OPERATION

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

In registration mode, insert the key into the ignition key cylinder and check the security indicator light.

HINT:

If the new key ID code registration fails, code 2-1 will be output through the security light. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key ID codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The output details are shown in the following illustration.


B111593
2.958,3.906 3.063,4.219 false 2.958,6 3.063,6.313 false 2.958,8.094 3.083,8.448 false 1.083,1.198 2.667,2.063 1.583,0.865 10 *2 1.083,3.083 1.917,3.302 0.833,0.219 10 *3 1.083,5.219 1.917,5.448 0.833,0.229 10 *4 1.083,7.302 1.906,7.542 0.823,0.24 10 *5 2.01,0.729 3.031,0.927 1.021,0.198 10 0.12 seconds 2.896,2.104 3.802,2.365 0.906,0.26 10 1.88 seconds 1.708,1.271 2,1.51 0.292,0.24 10 On 1.677,1.708 2.115,1.927 0.438,0.219 10 Off 1.74,3.177 2,3.438 0.26,0.26 10 On 1.719,3.615 2.115,3.813 0.396,0.198 10 Off 1.76,5.26 2.073,5.521 0.313,0.26 10 On 1.729,5.698 2.115,5.938 0.385,0.24 10 Off 2.01,2.531 2.927,2.719 0.917,0.188 10 0.25 seconds 1.458,3.938 2.375,4.104 0.917,0.167 10 0.25 seconds 2.865,4.24 3.948,4.458 1.083,0.219 10 0.5 seconds 3.365,2.729 3.99,2.948 0.625,0.219 10 1 second 1.771,7.365 2.083,7.594 0.313,0.229 10 On 1.76,7.802 2.156,8.021 0.396,0.219 10 Off 2.052,4.625 3.115,4.802 1.063,0.177 10 0.25 seconds 3.688,4.844 4.406,5.042 0.719,0.198 10 1 second 1.469,6.031 2.49,6.219 1.021,0.188 10 0.25 seconds 2.823,6.354 3.698,6.542 0.875,0.188 10 0.5 seconds 2.042,6.698 2.958,6.854 0.917,0.156 10 0.25 seconds 1.49,8.104 2.417,8.26 0.927,0.156 10 0.25 seconds 4.052,6.917 4.729,7.125 0.677,0.208 10 1 second 2.854,8.49 3.792,8.677 0.938,0.188 10 0.5 seconds 0.729,0.167 1.583,0.51 0.854,0.344 10 *1
*1 Security Indicator Light *2 Normal (Immobiliser system is operating normally)
*3 Code 2-1 *4 Code 2-2
*5 Code 2-3 - -



Result:
Proceed to
Code 2-1 or Code 2-3 is output
Code 2-2 is output



Code 2-1 or Code 2-3 is output

3.READ VALUE USING TECHSTREAM (TRANSPONDER S-CODE, TRANSPONDER M-CODE)

Code 2-2 is output

END (REGISTERED KEY WAS USED)

3.READ VALUE USING TECHSTREAM (TRANSPONDER S-CODE, TRANSPONDER M-CODE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Immobiliser / Data List.


e.

Read the Data List according to the display on the Techstream.

Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Transponder S-code Number of registered sub keys Min.: 0, Max.: 15 Number of registered sub keys -
Transponder M-code Number of registered master keys Min.: 0, Max.: 15 Number of registered master keys -
Body Electrical > Immobiliser > Data List
Tester Display
Transponder S-code
Transponder M-code
50003 260 20,19

Result:
Result Proceed to
5 is displayed for "Transponder M-code" and 0 is displayed for "Transponder S-code" A
0 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code" B
5 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code" C
Values are other than above D



A

KEY REGISTRATION (SUB-KEY)

B

KEY REGISTRATION (MASTER KEY)

C

MAXIMUM NUMBER OF KEYS ALREADY REGISTERED

D

4.KEY REGISTRATION
4.KEY REGISTRATION
a.

Refer to the table below to determine if additional keys can be registered.

Number of Keys Registered (Master and Sub) Proceed to
0 New key ID code registration
1 to 7 Additional key ID code registration


b.

Check if an additional key can be registered.

OK:

Additional key can be registered.



Result:
Proceed to
OK
NG



OK

END (KEY MALFUNCTION)

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)
a.

Disconnect the G7 unlock warning switch assembly connector.


b.

Disconnect the G88 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-1 - G88-3 (KSW) Always Below 1 Ω
G7-2 - Body ground Always Below 1 Ω
G7-1 - Body ground Always 10 kΩ or higher
G88-3 (KSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR