Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Key System)
RM30B0U _58 Vehicle Interior _009405 THEFT DETERRENT / KEYLESS ENTRY _0059576 IMMOBILISER SYSTEM(w/o Smart Key System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Key System)  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

B344497
1.469,0.875 1.677,1.052 0.208,0.177 10 false 13 1.667,0.99 1.875,1.167 0.208,0.177 10 false E 2.385,0.979 2.594,1.156 0.208,0.177 10 false LP 2.698,0.823 2.906,1 0.208,0.177 10 false 21 1.396,1.667 1.854,1.854 0.458,0.188 10 false G43 1.427,1.875 3.375,2.24 1.948,0.365 10 false Security Indicator Light (Telltale Light Assembly) 4.479,0.854 4.688,1.031 0.208,0.177 10 false 8 4.74,0.979 5.125,1.156 0.385,0.177 10 false IND 4.656,1.552 5.188,1.74 0.531,0.188 10 false G88 4.656,1.75 6.802,1.979 2.146,0.229 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Registration.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Key System)>REGISTRATION

·

When using the Techstream with the vehicle ignition switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.



PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SECURITY INDICATOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON or OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the Techstream.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TELLTALE LIGHT ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TELLTALE LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the G88 transponder key ECU assembly connector.


b.

Disconnect the G43 security indicator light (telltale light assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G43-21 (LP) - G88-8 (IND) Always Below 1 Ω
G43-21 (LP) - Body ground Always 10 kΩ or higher
G88-8 (IND) - Body ground Always 10 kΩ or higher
G43-13 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the G88 transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G43-21 (LP) - Body ground Key not in ignition key cylinder Pulse generation
Key in ignition key cylinder Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

NG