1.DESCRIPTION OF CODE REGISTRATION
Registering an ID code enables the entry and start function, wireless door lock control function and engine immobiliser function to be operated.
Code registration is needed when the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly) or electrical key transmitter sub-assembly is replaced with a new one.
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
This vehicle does not have a key slot. Therefore, while facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch as shown in the illustration to register the electrical key transmitter sub-assembly.
Once any of the following components has been registered to the vehicle, it cannot be used in another vehicle.
- Electrical key transmitter Sub-assembly
- Certification ECU (smart key ECU assembly)
- Steering lock ECU (steering lock actuator assembly)
2.KEY REGISTRATION PROCEDURES WHEN ADDING OR REPLACING KEY OR WHEN KEY IS LOST
The following procedures require the use of the Techstream:
- New key ID registration
- Additional key ID registration
- Key ID erasure
A maximum of 7 keys can be registered (this includes any keys registered when the vehicle was purchased).
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Customer Request/Condition | Registration Procedure Condition | Procedure | Refer to |
|---|---|---|---|
| Registering additional key | Customer must bring at least 1 key | 1. Register additional keys as necessary (additional key ID registration) | PROCEDURE "C" |
·
Replacing a key (e.g., when replacing an old key with a new one) ·
Making a lost key unusable
|
Customer must bring at least 1 key | 1. Using remaining key, clear all registered keys except one (key ID erasure) | PROCEDURE "D" |
| 2. Register additional keys as necessary (additional key ID registration) | PROCEDURE "C" | ||
| All keys are lost | - | 1. Reset all keys (all keys ID erasure [key code reset]) | PROCEDURE "E" |
| 2. Register all keys (new key ID registration) | PROCEDURE "A" |
3.PART REPLACEMENT AND KEY REGISTRATION PROCEDURES
If a malfunctioning ECU is discovered through troubleshooting of the smart key system, use the ECU replacement and key registration procedures in the table below.
When the certification ECU (smart key ECU assembly) is replaced, confirm that no key has already been registered in the certification ECU (smart key ECU assembly). If any key has already been registered, it is possible that the certification ECU (smart key ECU assembly) is a secondhand one, and the key cannot be registered.
When the registration operation is performed once on the certification ECU (smart key ECU assembly), the steering lock actuator assembly (steering lock ECU), or the electrical key transmitter sub-assembly, do not return these components. Since information once been registered cannot be deleted, these components cannot be used for other vehicle.
The following procedures require the use of the Techstream:
- New key ID registration
- Additional key ID registration
- Key ID erasure
- ECU code registration
A maximum of 7 keys can be registered (this includes any keys registered when the vehicle was purchased).
Immediately after replacing the certification ECU (smart key ECU assembly), the Techstream item "A number of registered codes" should change to "0". If this item does not change to "0", the certification ECU (smart key ECU assembly) may be registered to another vehicle. A certification ECU (smart key ECU assembly) which is registered to another vehicle cannot be used.
Once any of the following components has been registered to the vehicle, it cannot be used in another vehicle.
- Electrical key transmitter Sub-assembly
- Certification ECU (smart key ECU assembly)
- Steering lock ECU (steering lock actuator assembly)
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Malfunctioning ECU | Condition | Procedure | Refer to | |
|---|---|---|---|---|
| Certification ECU (smart key ECU assembly) | Customer has brought all keys | 1. Replace certification ECU (smart key ECU assembly) | - | |
| 2. Reregister all customer's keys | PROCEDURE "B"* | |||
| 3. ECU communication ID registration | PROCEDURE "G"* | |||
| Some keys are lost | Key ID codes can be registered and cleared | 1. Clear key codes (key ID erasure) | PROCEDURE "D" | |
2. Perform additional key registration procedure (additional key ID registration)
|
PROCEDURE "C"* | |||
| 3. Replace certification ECU (smart key ECU assembly) | - | |||
| 4. Register all keys (all keys which customer brings and additional new keys if requested). | PROCEDURE "B" | |||
| 5. ECU communication ID registration | PROCEDURE "G" | |||
| Certification ECU (smart key ECU assembly) | Some keys are lost | Key ID codes cannot be either registered or cleared | 1. Replace certification ECU (smart key ECU assembly) | - |
| 2. Replace steering lock ECU (steering lock actuator assembly) | - | |||
3. Reregister all keys (new key ID registration)
|
PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| All keys are lost | 1. Replace certification ECU (smart key ECU assembly) | - | ||
| 2. Replace steering lock ECU (steering lock actuator assembly) | - | |||
| 3. Register all keys (new key ID registration) | PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| Steering lock ECU (steering lock actuator assembly) | Customer has brought at least 1 key | 1. Replace steering lock ECU (steering lock actuator assembly) | - | |
| 2. Register recognition codes in ECUs (ECU code registration) | PROCEDURE "F" | |||
| All keys are lost | 1. Replace certification ECU (smart key ECU assembly) | - | ||
| 2. Replace steering lock ECU (steering lock actuator assembly) | - | |||
| 3. Register all keys (new key ID registration) | PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| ECM | When replacing the ECM with a new one. | 1. Replace ECM | - | |
| Replace the ECM with used one. | 1. Replace ECM | - | ||
| 2. ECU communication ID registration | PROCEDURE "G" | |||
* : It is only necessary to perform processes 1 through 3.
4.KEY REGISTRATION (PROCEDURE "A")
New key ID registration:
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Process | Procedure |
|---|---|
| 1. Start of registration | 1.
Prepare all new keys to be registered and place them outside vehicle. Bring 1 new key inside vehicle. 2.
Connect Techstream to DLC3 3.
While holding new key, turn engine switch on (IG)
4.
Turn Techstream on 5.
Enter following menus: Smart Key / Utility / Smart Code Registration |
| 2. Confirmation of ECU code | Perform operation according to prompts on Techstream screen
|
| 3. Verification of unregistered key* | 1.
While facing logo side of unregistered transmitter toward engine switch, hold transmitter near engine switch. 2.
Confirm that wireless door lock buzzer sounds twice (short beep) 3.
Bring key for which operations have been completed outside vehicle. Then bring another new key for which operations are to be performed into vehicle. |
| 4. Registration of ID code | Perform operation according to prompts on Techstream screen |
| 5. End of registration | Finish new key ID code registration |
*: Repeat this process for each key which is to be registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys is not finished within the specified time, perform the registration from process 1 again.
If "Smart Key System" is canceled, registration cannot be performed.
5.KEY REGISTRATION (PROCEDURE "B")
New key ID registration:
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Process | Procedure |
|---|---|
| 1. Start of registration | 1.
Prepare all registered keys and any keys to be registered and place them outside vehicle. Bring 1 registered key inside vehicle. 2.
Connect Techstream to DLC3 3.
While holding registered key, turn engine switch on (IG)
4.
Turn Techstream on 5.
Enter following menus: Smart Key / Utility / Smart Code Registration |
| 2. Confirmation of ECU code | Perform operation according to prompts on Techstream screen
|
| 3. Confirmation of all registered keys*1 | 1.
While facing logo side of registered transmitter toward engine switch, hold transmitter near engine switch. 2.
Confirm that wireless door lock buzzer sounds once (short beep) 3.
Bring key for which operations have been completed outside vehicle. Then bring another key for which operations are to be performed into vehicle. |
| 4. Confirmation of ECU code | Perform operation according to prompts on Techstream screen |
| 5. Verification of unregistered key*2 | 1.
While facing logo side of unregistered transmitter toward engine switch, hold transmitter near engine switch. 2.
Confirm that wireless door lock buzzer sounds twice (short beep) 3.
Bring key for which operations have been completed outside vehicle. Then bring another key for which operations are to be performed into vehicle. |
| 6. Registration of ID code | Perform operation according to prompts on Techstream screen |
| 7. End of registration | Finish new key ID code registration |
*1: Repeat this process for each key registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys is not finished within the specified time, perform the registration from process 1 again. When performing the key confirmation procedure for a key, the security indicator light comes on and remains on until all the keys are confirmed.
*2: Repeat this process for each key which is to be registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys is not finished within the specified time, perform the registration from process 1 again.
If "Smart Key System" is canceled, registration cannot be performed.
6.KEY REGISTRATION (PROCEDURE "C")
Additional key ID registration:
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Process | Procedure |
|---|---|
| 1. Start of registration | 1.
Prepare all keys to be registered and place them outside vehicle. Then bring 1 registered key into vehicle. 2.
Connect Techstream to DLC3 3.
While holding registered key, turn engine switch on (IG) 4.
Turn Techstream on 5.
Enter following menus: Smart Key / Utility / Smart Code Registration |
| 2. Confirmation of registered key*1 | 1.
Perform operation according to prompts on Techstream screen 2.
While facing logo side of registered transmitter toward engine switch, hold transmitter near engine switch. 3.
Confirm that wireless door lock buzzer sounds once (short beep) |
| 3. Confirmation of ECU code | Perform operation according to prompts on Techstream screen |
| 4. Verification of unregistered key*2 | 1.
While facing logo side of unregistered transmitter toward engine switch, hold transmitter near engine switch. 2.
Confirm that wireless door lock buzzer sounds twice (short beep) |
| 5. Registration of ID code | Perform operation according to prompts on Techstream screen |
| 6. End of registration | Finish key ID code registration |
*1: Perform this process for one of the keys registered to the vehicle. Finish the procedure within 30 seconds. If the procedure is not finished within the specified time, perform the registration from process 1 again.
*2: Repeat this process for each key which is to be registered to the vehicle. Finish the procedure for each key within 30 seconds. If the procedure for any of the keys is not finished within the specified time, perform the registration from process 1 again.
If "Smart Key System" is canceled, registration cannot be performed.
7.KEY REGISTRATION (PROCEDURE "D")
Key ID erasure:
This procedure clears all the registered key codes except one master key code.
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Process | Procedure |
|---|---|
| 1. Start of erasure | 1.
Connect Techstream to DLC3 2.
While holding registered key, turn engine switch on (IG) 3.
Turn Techstream on 4.
Enter following menus: Smart Key / Utility / Smart Code Erasure |
| 2. Confirmation of registered key* | 1.
Perform operation according to prompts on Techstream screen 2.
While facing logo side of registered transmitter toward engine switch, hold transmitter near engine switch. 3.
Confirm that wireless door lock buzzer sounds once (short beep) |
| 3. Confirmation of ECU code | Perform operation according to prompts on Techstream screen |
| 4. Erasure of ID code | Perform operation according to prompts on Techstream screen |
| 5. End of erasure | Finish key ID code erasure |
*: Perform this process for one of the keys registered to the vehicle. Finish the procedure within 30 seconds. If the procedure is not finished within the specified time, perform the erasure from process 1 again.
If "Smart Key System" is canceled, registration cannot be performed.
8.KEY REGISTRATION (PROCEDURE "E")
All keys ID erasure:
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Process | Procedure |
|---|---|
| 1. Start of erasure | 1.
Connect Techstream to DLC3 2.
While holding registered key, turn engine switch on (IG) 3.
Turn Techstream on 4.
Enter following menus: Smart Key / Utility / Smart Code Reset 5.
Read "Seed Number" sent from TIS according to Techstream screen 6.
Input "Pass-Code Number" sent from TIS according to Techstream screen |
| 2. Confirmation of ECU code | Perform operation according to prompts on Techstream screen |
| 3. Erasure of ID code | 1.
Perform operation according to prompts on Techstream screen 2.
Wait for 15 minutes |
| 4. End of erasure | Finish key ID code erasure |
If "Smart Key System" is canceled, registration cannot be performed.
9.KEY REGISTRATION (PROCEDURE "F")
ECU code registration:
In the chart below, the numbers in the "Procedure" column (1, 2, 3, etc.) indicate the step numbers. Perform the steps in numerical order.
| Process | Procedure |
|---|---|
| 1. Start of registration | 1.
Connect Techstream to DLC3 2.
While holding registered key, turn engine switch on (IG)
3.
Turn Techstream on 4.
Enter following menus: Smart Key / Utility / ECU Communication ID Registration / ID code box and Steering Lock |
| 2. Confirmation of registered key* | 1.
While facing logo side of registered transmitter toward engine switch, hold transmitter near engine switch. 2.
Confirm that wireless door lock buzzer sounds once (short beep) |
| 3. Erasure of ECU code | Perform operation according to prompts on Techstream screen |
| 4. End of registration | Finish ECU code registration |
*: Perform this process for one of the keys registered to the vehicle. Finish the procedure within 30 seconds. If the procedure is not finished within the specified time, perform the registration from process 1 again.
If "Smart Key System" is canceled, registration cannot be performed.
If there are any electronic devices near the driver seat which may cause wave interference, such as cell phones, personal computers, portable music players, other electrical key transmitter sub-assemblies, etc., turn them off or move them away from the driver seat.
10.KEY REGISTRATION (PROCEDURE "G")
ECU communication ID registration:
The ECU communication ID should be registered when the certification ECU (smart key ECU assembly) is replaced in order for the ECU communication ID to match.
The engine cannot be started unless the ECU communication ID is registered.
After registration, pressing the engine switch may not start the engine on the first try. If so, press the engine switch again.
After the engine is started, clear DTC B2799 (code for ECM immobiliser communication error) using either of the following methods:
- Use the Techstream.
- Disconnect the cable from the negative (-) battery terminal for 30 seconds.
| *1 | SST |
| *a | DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the engine switch on (IG) (do not start the engine) and leave it as is for 30 minutes.
Turn the engine switch off and disconnect terminals 13 (TC) and 4 (CG).
Check that the engine starts and stays on for more than 3 seconds.