Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM30B0U _57 Power Source / Network _009133 NETWORKING _0059674 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock actuator stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2786 No Response from Steering Lock ECU Communication between the certification ECU (smart key ECU assembly) and steering lock ECU stops for 10 seconds or more.
·

Steering lock actuator assembly

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B339675
0.708,1.365 2.5,1.823 1.792,0.458 10 Certification ECU (Smart Key ECU Assembly) 0.698,1.188 1.156,1.385 0.458,0.198 10 G84 1.813,0.76 2.271,0.958 0.458,0.198 10 LIN 5.094,0.75 5.552,0.948 0.458,0.198 10 LIN 0.646,3.438 2.448,3.75 1.802,0.313 10 : LIN Communication Line 4.51,3.031 6.76,3.375 2.25,0.344 10 Steering Lock Actuator Assembly 4.5,2.844 4.813,3.042 0.313,0.198 10 G5 4.927,0.604 5.083,0.802 0.156,0.198 10 5 2.115,0.615 2.427,0.813 0.313,0.198 10 17 4.927,1.646 5.083,1.844 0.156,0.198 10 7 5.104,1.75 5.26,1.948 0.156,0.198 10 B 4.927,2.229 5.083,2.427 0.156,0.198 10 1 5.104,2.365 5.563,2.563 0.458,0.198 10 GND 2.802,1.729 3.646,2.031 0.844,0.302 10 from Battery 3.927,1.969 4.823,2.208 0.896,0.24 10 STRG LOCK

CAUTION / NOTICE / HINT

NOTICE:
·

When using the Techstream with the ignition switch off to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart key system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART KEY SYSTEM(for Entry Function)>PRECAUTION



HINT:

When the communication between the steering lock actuator assembly and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC B2786 is output
DTC B2786 is not output



DTC B2786 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR ASSEMBLY)

DTC B2786 is not output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR ASSEMBLY)
a.

Disconnect the G84 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the steering lock actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-17 (LIN) - G5-5 (LIN) Always Below 1 Ω
G84-17 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY AND BODY GROUND)
B291261
1.521,0.354 1.875,0.594 0.354,0.24 0.75,1.656 1.167,1.24 false 2.677,1.594 2.302,1.229 false 0.083,0.052 0.396,0.25 0.313,0.198 10 *a 0.406,1.594 0.865,1.792 0.458,0.198 10 GND 2.75,1.563 2.906,1.76 0.156,0.198 10 B 1.594,0.375 1.906,0.573 0.313,0.198 10 G5
*a Front view of wire harness connector
(to Steering Lock Actuator Assembly)


a.

Disconnect the G5 steering lock actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G5-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
a.

Temporarily replace the steering lock actuator assembly with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Smart Key > Trouble Codes
50001 125

Result:
Proceed to
DTC B2786 is not output
DTC B2786 is output



DTC B2786 is not output

END (STEERING LOCK ACTUATOR ASSEMBLY IS DEFECTIVE)

DTC B2786 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)