Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › TRANSFER OIL
RM30B0U _52 Drivetrain _009983 GF1A TRANSFER / 4WD / AWD _0060049 TRANSFER OIL A

GF1A TRANSFER / 4WD / AWD  TRANSFER OIL  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN TRANSFER OIL

a.

Stop the vehicle on a level surface.


b.
C277146
1.521,0.594 1.927,0.417 1.927,0.417 2.063,0.417 true 1.698,1.646 1.896,1.896 1.896,1.896 2.052,1.896 true 2.156,0.333 2.469,0.531 0.313,0.198 10 *1 2.156,1.781 2.469,1.979 0.313,0.198 10 *2
*1 No. 2 Transfer Case Plug (for filler)
*2 Transfer Drain Plug


Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the No. 2 transfer case plug (for filler) and gasket.


c.

Using a 10 mm hexagon socket wrench, remove the transfer drain plug and gasket and drain the transfer oil.


d.

Using a 10 mm hexagon socket wrench, install a new gasket and the drain plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 2.ADD TRANSFER OIL

a.

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the No. 2 transfer case plug (for filler) and gasket.


b.

Add transfer oil.

Oil grade:

Toyota Genuine Differential gear oil LT API GL-5 or equivalent


Viscosity:

SAE 75W-85



c.
C278961
2.667,0.854 2.979,1.052 0.313,0.198 10 false *a
*a 0 to 5.0 mm (0 to 0.196 in.)


Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.196 in.) from the bottom lip of the No. 2 transfer case plug (for filler) hole.

NOTICE:
·

When adding oil, pour it slowly.

·

Add oil a little at a time, waiting several minutes between each addition of oil.

·

Too much or too little oil will lead to transfer problems.



Standard Capacity:

0.40 to 0.50 liters (0.43 to 0.52 US qts, 0.36 to 0.44 Imp.qts)



d.

Wait approximately 5 minutes and check that the oil level has not changed.


e.
C277145
0.698,4.458 0.563,4.458 0.563,4.458 0.365,4.177 true 0.99,3.99 1.073,4.313 1.073,4.313 1.198,4.313 true 1.49,4 1.625,4.365 1.625,4.365 1.76,4.365 true 0.771,4.375 1.083,4.573 0.313,0.198 10 *1 1.844,4.281 2.156,4.479 0.313,0.198 10 *2 1.271,4.229 1.583,4.427 0.313,0.198 10 *3
*1 10 mm Straight Hexagon Wrench
*2 12 mm Hexagon Socket Wrench
*3 10 x 12 mm Long Offset Wrench


Using a 10 mm straight hexagon wrench, 12 mm hexagon socket wrench and 10 x 12 mm long offset wrench, install a new gasket into the No. 2 transfer case plug (for filler) and then install the No. 2 transfer case plug (for filler).

Torque:
39 N*m (398 kgf*cm, 28 ft.*lbf)

NOTICE:
·

Use the formula to calculate special torque values for situations where a offset wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After adding oil, drive the vehicle and recheck the oil level.



HINT:

When tightening, combine the offset wrench with the torque wrench so that they are in a straight line.