Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM30B0U _52 Drivetrain _010989 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0060247 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0746  Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)  


DESCRIPTION

The ECM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves and valve body.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) Either condition is met (2-trip detection logic):
·

The engine revs freely when a shift to 1st, 2nd, 3rd or 4th gear is commanded.

·

Either condition is met twice:

·

When a shift to 5th gear is commanded, 4th gear is engaged.

·

When a shift to 6th gear is commanded, 4th gear is engaged.



·

Shift solenoid valve SL1 remains open or closed

·

Transmission valve body assembly is blocked

·

Automatic transaxle assembly (clutch, brake or gear etc.)


Comes on DTC stored

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft speed, intermediate (counter) shaft speed and output shaft speed, the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Related DTCs P0746:
Shift solenoid valve SL1/OFF malfunction/Functional check
Shift solenoid valve SL1/ON malfunction/Functional check
Required sensors/Components Shift solenoid valve SL1, Speed sensor (NT), Speed sensor (NC), Crankshaft position sensor (NE)
Frequency of operation Continuous
Duration OFF malfunction: 0.5 sec.
ON malfunction: 0.8 sec.
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not stored P0712, P0713 (ATF temperature sensor circuit)
P0115, P0117, P0118 (ECT sensor circuit)
P0715, P0717 (Turbine speed sensor circuit)
P0791, P0793 (Intermediate shaft speed sensor circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0798 (Shift solenoid valve SL3 circuit)
P2810 (Shift solenoid valve SL4 circuit)
P0327, P0328 (KCS sensor circuit)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 (ETCS)
U0100 (CAN communication system)
ATF temperature sensor circuit Not circuit malfunction
ECT (Engine coolant temperature) sensor circuit Not circuit malfunction
Turbine speed sensor circuit Not circuit malfunction
Intermediate shaft speed sensor circuit Not circuit malfunction
Shift solenoid valve SL1 circuit Not circuit malfunction
Shift solenoid valve SL2 circuit Not circuit malfunction
Shift solenoid valve SL3 circuit Not circuit malfunction
Shift solenoid valve SL4 circuit Not circuit malfunction
KCS (Knock control sensor) circuit Not circuit malfunction
ETCS (Electronic throttle control system) Not system down
CAN communication system Not system down
Transmission range "D"
Duration time from shifting "N" to "D" 4 sec. or more
ATF temperature -10°C (14°F) or higher
Engine Starting

OFF malfunction
ECM selected gear 1st, 2nd, 3rd or 4th
ECM indicated pressure value of SL1 1200 kPa (12.2 kgf/cm2, 174 psi)
Throttle valve opening angle 3% or more

ON malfunction
ECM selected gear 5th or 6th
Vehicle speed 2 km/h (1.2 mph) or more
ETC 40°C (104°F) or higher
Throttle valve opening angle 6.5% or more at engine speed of 2000 rpm (Condition varies with engine speed)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
OFF malfunction
Turbine speed - Output speed x Gear ratio 1000 rpm or more


[ON malfunction]

2 detections are necessary per driving cycle:

1st detection: temporary flag ON

2nd detection: pending fault code ON

ON malfunction
Turbine speed / Output speed when output speed less than 1000 rpm 0.976 to 1.113


CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION

·


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0746)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the Techstream.

Result:
Result Proceed to
Only P0746 is output A
P0746 and other DTCs are output B


HINT:

If shift solenoid valve SL1 is stuck off, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.




A

3.INSPECT SHIFT SOLENOID VALVE SL1

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (DRIVING TEST)
2.PERFORM ACTIVE TEST USING TECHSTREAM (DRIVING TEST)
NOTICE:

This test should always be performed with at least 2 people.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the Techstream, perform the Active Test.

HINT:
·

Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

·

The gear commanded by the ECM is shown in the Data List / Shift Status display on the Techstream.



Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operate the shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Can be used to check the operation of the shift solenoid valves.
A 10-second interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transaxle.
[Vehicle Condition]
50 km/h (30 mph) or less
Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Shift Position
Data List Display
Shift Status
50004 234 116 416
NOTICE:
·

This test can be conducted when the vehicle is stopped.

·

When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.




h.

Check the vehicle speed and the gear when the engine speed is 1000 rpm.

HINT:

Because the torque converter has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th and 6th gear, however a difference of speed should still be evident following each gear change.


Standard:
1st 2nd 3rd 4th 5th 6th
8 to 12 km/h (5 to 7.5 mph) 15 to 19 km/h (9.3 to 11.8 mph) 21 to 25 km/h (13.0 to 15.5 mph) 31 to 35 km/h (19.3 to 21.7 mph) 44 to 48 km/h (27.3 to 29.8 mph) 52 to 56 km/h (32.3 to 34.8 mph)



i.

Compare the ECM commanded gear and the actual gear.

Result:
System Condition ECM Gear Shift Command Proceed to
1st 2nd 3rd 4th 5th 6th
Malfunction Shift solenoid valve SL1 Stuck ON 1st 2nd 3rd 4th 4th 4th A
Shift solenoid valve SL1 Stuck OFF N*1 N*1 N*1 N*1 5th 6th
Shift solenoid valve SL2 Stuck ON 4th 4th 4th 4th 5th 6th B
Shift solenoid valve SL2 Stuck OFF 1st 2nd 3rd 1st N*1 N*1
Shift solenoid valve SL3 Stuck ON 2nd 2nd 3rd 4th 5th 6th C
Shift solenoid valve SL3 Stuck OFF 1st 1st 3rd 4th 5th N*1
Shift solenoid valve SL4 Stuck ON*3 3rd 3rd 3rd 4th 5th 5th D
Shift solenoid valve SL4 Stuck OFF 1st 2nd 1st 4th N*1 6th
Shift solenoid valve SLT Stuck ON N*2 N*2 N*2 N*2 N*2 N*2 E
Shift solenoid valve SLT Stuck OFF*3 1st 2nd 3rd 4th 5th 6th


HINT:
·

*1: Neutral

·

*2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is less than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.

·

*3: When shift solenoid valve SLT is stuck off, gear shifting is normal.





A

3.INSPECT SHIFT SOLENOID VALVE SL1

B

C

D

E

3.INSPECT SHIFT SOLENOID VALVE SL1
a.
C197715
1.781,0.969 2.167,0.427 true 1.781,2.948 2.167,2.406 true 1.469,0.969 1.083,0.417 true 1.469,2.948 1.083,2.396 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *1 2.198,0.323 2.375,0.542 0.177,0.219 10 1 2.198,2.302 2.375,2.521 0.177,0.219 10 1 0.969,0.323 1.146,0.542 0.177,0.219 10 2 0.969,2.313 1.146,2.531 0.177,0.219 10 2 1.854,3.938 2.313,4.135 0.458,0.198 10 (+) 1.271,3.938 1.729,4.135 0.458,0.198 10 (-)
*1 Shift Solenoid Valve SL1


Remove shift solenoid valve SL1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


OK:

There are no foreign objects on any valve.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY