Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM30B0U _52 Drivetrain _010989 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0060247 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to DTC P2714.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>P2714

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) An open or short is detected in the shift solenoid valve SLT circuit for 1 sec. or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will turn on the MIL and store the DTC.

MONITOR STRATEGY

Related DTCs P2716: Shift solenoid valve SLT/Range check
Required sensors/Components Shift solenoid valve SLT
Frequency of operation Continuous
Duration 1 sec.
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
The monitor will run whenever the following DTCs are not stored None
Solenoid current cut status Not cut
Ignition switch ON
Starter OFF

Malfunction (A)
Battery voltage 12 V or higher
Target current 1 A

Malfunction (B)
Battery voltage 10 V or higher and below 12 V
Target current Below 0.75 A

Malfunction (C)
Battery voltage 8 V or higher
Target current 1 A

Malfunction (D)
Battery voltage 11 V or higher
Target current 1 A or higher

Malfunction (E)
Battery voltage 11 V or higher
Target current 0.1 A or higher
Target voltage - Last Target voltage Below 0.000019 V

TYPICAL MALFUNCTION THRESHOLDS

Malfunction (A) and (B)
Output duty cycle 100% or more

Malfunction (C)
Output duty cycle 0% or less

Malfunction (D)
Solenoid voltage monitor No signal

Malfunction (E)
Target voltage - Average of monitor voltage 0.035 V or higher

COMPONENT OPERATING RANGE

Output duty cycle Less than 100%

WIRING DIAGRAM

C239277
5.656,4.333 6.083,4.521 0.427,0.188 10 false ECM 5.104,1.229 5.531,1.417 0.427,0.188 10 false SLT+ 5.104,2.635 5.531,2.823 0.427,0.188 10 false SLT- 3.615,1.25 4.042,1.438 0.427,0.188 10 false SLT+ 3.615,2.646 4.042,2.833 0.427,0.188 10 false SLT- 1.604,1.927 2.542,2.26 0.938,0.333 10 false Shift Solenoid Valve SLT 1.177,3.417 2.531,3.604 1.354,0.188 10 false Transmission Wire 3.052,3.427 4.052,3.781 1,0.354 10 false Wiring Harness Connector 3.094,1.25 3.521,1.438 0.427,0.188 10 false SLT+ 3.094,2.646 3.521,2.833 0.427,0.188 10 false SLT- 2.302,1.25 2.729,1.438 0.427,0.188 10 false SLT+ 2.302,2.646 2.729,2.833 0.427,0.188 10 false SLT- 5.656,4.177 5.938,4.333 0.281,0.156 10 false B77 4.802,1.479 5,1.635 0.198,0.156 10 false 15 4.802,2.865 5,3.021 0.198,0.156 10 false 14 2.844,2.552 2.969,2.719 0.125,0.167 10 false 7 2.781,1.167 2.979,1.323 0.198,0.156 10 false 12 4.125,2.552 4.26,2.719 0.135,0.167 10 false 7 4.073,1.167 4.271,1.323 0.198,0.156 10 false 15 2.833,2.76 3.115,2.917 0.281,0.156 10 false A 2.823,1.375 3.104,1.531 0.281,0.156 10 false A 4.031,2.76 4.313,2.917 0.281,0.156 10 false B78 4.021,1.365 4.302,1.521 0.281,0.156 10 false B78 1.417,1.708 1.844,1.896 0.427,0.188 10 false 1 1.417,2.365 1.844,2.552 0.427,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION

·


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SLT CIRCUIT)
a.
C267934
1.448,0.177 1.865,0.385 0.417,0.208 0.948,1.719 1.25,0.885 true 1.771,1.708 1.313,0.885 true 1.531,0.208 1.99,0.406 0.458,0.198 10 false B77 0.677,1.75 1.385,1.969 0.708,0.219 10 false 14 (SLT-) 1.563,1.75 2.281,1.969 0.719,0.219 10 false 15 (SLT+) 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-15 (SLT+) - B77-14 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
B77-15 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
B77-14 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
a.

Disconnect the B78 wiring harness connector.


b.

Disconnect the B77 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-15 (SLT+) - B77-15 (SLT+) Always Below 1 Ω
B78-7 (SLT-) - B77-14 (SLT-) Always Below 1 Ω
B78-15 (SLT+) or B77-15 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
B78-7 (SLT-) or B77-14 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C226545
0.594,0.76 0.938,1 0.344,0.24 2.083,1.5 1.885,0.969 true 1.604,1.51 1.771,0.792 true 0.354,0.219 0.667,0.417 0.313,0.198 10 *a 1.948,1.552 2.563,1.75 0.615,0.198 10 SLT+ 0.708,0.792 1.063,0.99 0.354,0.198 10 A 1.438,1.552 2.052,1.75 0.615,0.198 10 SLT-
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-12 (SLT+) - A-7 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
A-12 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
A-7 (SLT-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE SLT
a.
C197715
1.781,0.969 2.167,0.427 true 1.781,2.948 2.167,2.406 true 1.469,0.969 1.083,0.417 true 1.469,2.948 1.083,2.396 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *1 2.198,0.323 2.375,0.542 0.177,0.219 10 1 2.198,2.302 2.375,2.521 0.177,0.219 10 1 0.969,0.323 1.146,0.542 0.177,0.219 10 2 0.969,2.313 1.146,2.531 0.177,0.219 10 2 1.854,3.938 2.313,4.135 0.458,0.198 10 (+) 1.271,3.938 1.729,4.135 0.458,0.198 10 (-)
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG