Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM30B0U _52 Drivetrain _010989 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0060247 AUTOMATIC TRANSAXLE SYSTEM J

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  Pattern Select Switch Sport Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and sport shift patterns.

By following the programs corresponding to the signals from the combination switch assembly, park/neutral position switch and other various sensors, the ECM switches the shift solenoid valves on and off, and controls the transaxle gear ratio.

WIRING DIAGRAM

C278992
5.833,3.177 6.292,3.375 0.458,0.198 10 false ECM 5.823,2.979 6.281,3.177 0.458,0.198 10 false A62 5.604,1.375 6.323,1.573 0.719,0.198 10 false PWMS 5.406,1.479 5.563,1.677 0.156,0.198 10 false 9 2.563,1.958 3.021,2.156 0.458,0.198 10 false G60 2.563,2.167 5.313,2.365 2.75,0.198 10 false Combination Switch 3.396,1.26 4.01,1.458 0.615,0.198 10 false MSW1 2.552,1.26 3.167,1.458 0.615,0.198 10 false MSW2 3.906,1.479 4.063,1.677 0.156,0.198 10 false 2 2.354,1.479 2.51,1.677 0.156,0.198 10 false 4

PROCEDURE

1.INSPECT COMBINATION SWITCH ASSEMBLY
a.
C277027
1.292,1.729 1.5,1.385 true 2.104,1.729 1.865,1.385 true 1.073,1.781 1.688,1.979 0.615,0.198 10 false MSW2 1.938,1.781 2.552,1.979 0.615,0.198 10 false MSW1 0.104,0.104 0.719,0.302 0.615,0.198 10 false *1
*1 Combination Switch Assembly


Remove the combination switch assembly.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>COMBINATION SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (MSW1) - 4 (MSW2) Combination switch (SPORT) on Below 1 Ω
2 (MSW1) - 4 (MSW2) Combination switch (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)
a.
C277026
0.458,0.927 0.854,1.177 0.396,0.25 2.177,1.75 1.927,1.333 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 2.01,1.792 2.625,1.99 0.615,0.198 10 MSW2 0.521,0.979 0.854,1.156 0.333,0.177 10 G60
*a Front view of wire harness connector
(to Combination Switch Assembly)


Disconnect the combination switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G60-4 (MSW2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)
a.
C267933
1.604,0.083 2.01,0.313 0.406,0.229 2.76,1.906 2.375,0.875 true 1.656,0.125 2.115,0.323 0.458,0.198 10 false A62 2.51,1.948 3.271,2.135 0.76,0.188 10 false 9 (PWMS) 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A62-9 (PWMS) - Body ground Combination switch (SPORT) on Below 1 Ω
A62-9 (PWMS) - Body ground Combination switch (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR