Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for LH Side)
RM30B0U _58 Vehicle Interior _009409 SEAT _0061281 REAR SEAT ASSEMBLY(for LH Side) A

SEAT  REAR SEAT ASSEMBLY(for LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.
B340941
1.771,1.49 2.104,0.406 2.104,0.406 2.406,0.406 false 2.469,0.281 2.781,0.438 0.313,0.156 10 *1
*1 Hog Ring Pliers


Set the separate type rear seatback cover in place.


b.

Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 11 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




c.
B340942
1.813,1.49 2.031,0.417 2.031,0.417 2.406,0.417 false 2.458,0.313 2.771,0.469 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 5 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




d.

Install the separate type rear seatback cover (with pad) to the rear seatback frame sub-assembly LH.


e.

Attach the 9 clamps.


f.

Attach the 8 claws to install the 4 rear seat headrest supports.


Hide 2.INSTALL REAR SEATBACK BOARD LH

a.

Attach the clamp and 7 claws to install the rear seatback board LH.


b.
B340946
1.823,1.521 2.021,0.396 2.021,0.396 2.344,0.396 false 2.396,0.313 2.708,0.469 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 6 new hog rings and attach the 2 pieces of fastening tape.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 3.INSTALL REAR NO. 1 SEATBACK ASSEMBLY LH

a.

Install the No. 1 seatback assembly LH to the rear seat reclining adjuster assembly LH with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 4.INSTALL REAR SEAT INNER BELT ASSEMBLY LH

a.

Install the rear seat inner belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 5.INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY

a.
B341755
0.229,0.51 0.385,0.708 0.156,0.198 10 1 1.01,0.792 1.167,0.99 0.156,0.198 10 2 3.219,2.51 3.375,2.708 0.156,0.198 10 1 2.656,2.813 2.813,3.01 0.156,0.198 10 2

Install the No. 2 seat adjuster control cable assembly in the order shown in the illustration.


b.

Attach the 2 clamps of the cable ends.


c.

Attach the 4 clamps.


Hide 6.INSTALL REAR SEAT REAR CUSHION MOULDING LH

a.

Attach the clamp and claw to install the rear seat rear cushion moulding LH.


b.

w/ Seat Belt Warning System:

Attach the 2 clamps.


Hide 7.INSTALL REAR SEATBACK COVER LH

a.

Attach the claw to install the rear seatback cover LH.


b.

Install the clip and screw.


Hide 8.INSTALL REAR SEAT COVER LH

a.

Attach the claw to install the rear seat cover LH.


b.

Install the clip and screw.


Hide 9.INSTALL REAR SEAT CUSHION MOULDING LH

a.

Attach the 3 hooks and claw to install the rear seat cushion moulding LH.


Hide 10.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.
B340943
1.844,1.479 2.031,0.427 2.031,0.427 2.375,0.427 false 2.448,0.292 2.76,0.448 0.313,0.156 10 *1
*1 Hog Ring Pliers


Set the separate type rear seat cushion cover in place.


b.

Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad LH with 13 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




c.
B340944
1.854,1.479 2.063,0.396 2.063,0.396 2.458,0.396 false 2.51,0.26 2.823,0.417 0.313,0.156 10 *1
*1 Hog Ring Pliers


Using hog ring pliers, install 5 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




d.

Install the separate type rear seat cushion cover (with pad) to the rear seat spring assembly with the 20 hooks.


Hide 11.INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY LH

a.

Install the No. 1 seat cushion assembly LH with the 2 bushes and 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 claws to install the rear seatback cover.


c.

Install the 3 clamps.


d.
B341756
0.448,1.135 0.604,1.333 0.156,0.198 10 1 0.833,0.594 0.99,0.792 0.156,0.198 10 2

Connect the cable in the order shown in the illustration.


e.

Attach the clamp of the cable end.


f.

Install the 2 bushes and 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.

Install the reclining adjuster release handle LH with the 3 screws.


Hide 13.INSTALL REAR SEATBACK NO. 1 BOARD CAP

a.

Attach the 3 claws to install the rear seatback No. 1 board cap.


Hide 14.INSTALL REAR SEAT NO. 1 CENTER ARMREST PLATE

a.

Install the rear seat No. 1 center armrest plate.


Hide 15.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.

Install the rear seat center armrest assembly with the washer and bolt.


Hide 16.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH

a.

Attach the clamp and 4 claws to install the rear seat lower cushion hinge cover LH.


Hide 17.INSTALL REAR SEAT NO. 3 CUSHION HINGE COVER

a.

Attach the clamp and 4 claws to install the rear seat No. 3 cushion hinge cover.


b.

Attach the clamp.


Hide 18.INSTALL CENTER ARMREST HINGE COVER RH

a.

Attach the clamp to install the center armrest hinge cover RH.


Hide 19.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH

Hide 20.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

Hide 21.INSTALL REAR SEAT HEADREST ASSEMBLY