Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM30B0U _59 Vehicle Exterior _009875 DOOR / HATCH _0061403 POWER BACK DOOR SYSTEM U

DOOR / HATCH  POWER BACK DOOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Back Door, Main Body or Smart Key* / Data List.

*: w/ Smart Key System



e.

According to the display on the Techstream, read the Data List.

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock Status Back door condition signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked
-
Half Latch SW Latch switch signal ON or OFF ON: Back door lock motor open-latched
OFF: Back door lock motor full-latched or half-latched
-
Closer Position SW Sector switch signal ON or OFF ON: Back door lock sector gear in center position
OFF: Back door lock sector gear out of center position
-
Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
OFF: Back door closed
-
PBD Touch Sensor (Right) Power back door sensor assembly RH signal ON, OFF or Open ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed
Open: Power back door sensor assembly RH circuit open
-
PBD Touch Sensor (Left) Power back door sensor assembly LH signal ON, OFF or Open ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed
Open: Power back door sensor assembly LH circuit open
-
PBD Main SW Power back door main switch signal ON or OFF ON: Power back door main switch pushed
OFF: Power back door main switch not pushed
-
PBD Close SW Door control switch assembly signal ON or OFF ON: Door control switch assembly pushed
OFF: Door control switch assembly not pushed
-
IG SW Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
"OFF" is also displayed for this item when the ignition switch is ACC.
PBD Position (3/4-Open) Load signal detected during back door closing operation (3/4 - Open) Caution or OK Caution: Load detected between back door 3/4 and fully open position during back door closing operation
OK: No load detected between back door 3/4 and fully open position during back door closing operation
-
PBD Position (2/4-3/4) Load signal detected during back door closing operation (2/4 - 3/4) Caution or OK Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation
OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation
-
PBD Position (1/4-2/4) Load signal detected during back door closing operation (1/4 - 2/4) Caution or OK Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation
OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation
-
PBD Position (Close-1/4) Load signal detected during back door closing operation (Close - 1/4) Caution or OK Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation
OK: No load detected between back door fully closed and 1/4 open position during back door closing operation
-
Closed Position Initialization Back door fully closed position memorized signal Not Initialized or Initialized Not Initialized: Back door fully closed position not memorized
Initialized: Back door fully closed position memorized
-
PBD SW Operation Power back door switch operation ON or 0.8 s Current customize setting displayed -
PBD Assist Open Operation Function that enables or disables the power back door assist open operation. When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. OFF or ON Current customize setting displayed -
PBD Assist Close Operation Function that enables or disables the power back door assist close operation. When PBD Assist Close is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. OFF or ON Current customize setting displayed -
Door Unlock with 1 Motion. Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch/Back Door or ALL DOORS Back Door or ALL DOORS Current customize setting displayed -
One Motion Function that operates the power back door by pushing the transmitter switch when the back door is locked or unlocked. OFF, 1 Op, 2 Op, 0.8s or Not Use Current customize setting displayed -
#Codes The number of DTCs Min.: 0
Max.: 255
The number of DTCs -
Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back Door Open Back door lock Permit or Prohibit Permit: Back door unlocked
Prohibit: Back door locked
-
Back Door Open SW Back door control switch signal ON or OFF ON: Back door control switch on
OFF: Back door control switch off
-
Back Door Open Handle SW Back door opener switch assembly signal ON or OFF ON: Back door opener switch assembly on
OFF: Back door opener switch assembly off
-
Body Electrical > Smart Key > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch assembly signal ON or OFF ON: Back door opener switch assembly on
OFF: Back door opener switch assembly off
-


ACTIVE TEST


HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Back Door / Active Test.


e.

According to the display on Techstream perform the "Active Test".

Body Electrical > Back Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Latch Release Latch release operation ON or OFF -
PBD Open/Close Power back door motor operation Forward, Reverse or OFF -
PBD Buzzer Power back door warning buzzer sound ON or OFF -