Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT
RM30B0U _52 Drivetrain _010989 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0058570 AUTOMATIC TRANSAXLE UNIT G

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 1.INSPECT TRANSMISSION OIL CLEANER MAGNET

a.

Examine particles in the automatic transaxle oil pan sub-assembly.

i.

Collect any steel chips with the removed magnets. Look carefully at the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.

Result:
Steel (magnetic):

Bearing, gear and plate wear

Brass (non-magnetic):

Bushing wear




Hide 2.INSPECT INPUT SHAFT END PLAY

a.
C136696

Using a dial indicator, measure the input shaft end play.

Standard end play:

0.020 to 1.242 mm (0.000788 to 0.0488 in.)



Hide 3.INSPECT INTERMEDIATE SHAFT END PLAY

a.
C201496
3.025,0.685 3.208,0.85 0.183,0.165 10 *a
*a Dimension A


Clean the contact surfaces of the transaxle case and rear transaxle cover sub-assembly.


b.

As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case and the straightedge using a vernier caliper (Dimension A).


c.
C138268
0.589,0.757 0.757,0.936 0.167,0.179 10 *a
*a Dimension B


Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).


d.

Calculate the end play value using the following formula:

End play = Dimension B - Dimension A - Thrust needle roller bearing thickness

Standard end play:

0.022 to 1.099 mm (0.000867 to 0.0432 in.)



Hide 4.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C138259

Using a caliper gauge, measure the inside diameter of the bushings of the planetary sun gear sub-assembly.

Standard inside diameter:

25.525 to 25.546 mm (1.00492 to 1.00574 in.)


Maximum inside diameter:

25.546 mm (1.00574 in.)


If the inside diameter is more than the maximum, replace the planetary sun gear sub-assemly.


Hide 5.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

a.
C201528

Using a caliper gauge, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.

Standard inside diameter:

25.580 to 25.601 mm (1.00709 to 1.00791 in.)


Maximum inside diameter:

25.601 mm (1.00791 in.)


If the inside diameter is more than the maximum, replace the automatic transaxle assembly.


Hide 6.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C200900

Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gears at 4 points.

Standard clearance:

0.18 to 0.54 mm (0.00709 to 0.0212 in.)


If the clearance is more than the standard clearance, replace the automatic transaxle assembly.


Hide 7.INSPECT ONE-WAY CLUTCH ASSEMBLY

a.
C189425
2.573,1.01 2.25,1.01 false 1.031,1.083 0.615,1.083 true 2.396,0.302 2.583,0.469 0.188,0.167 10 *b 0.563,0.302 0.75,0.458 0.188,0.156 10 *a 2.615,0.927 2.792,1.094 0.177,0.167 10 *2 0.417,0.99 0.583,1.146 0.167,0.156 10 *1
*1 Planetary Ring Gear
*2 One-way Clutch Assembly
*a Free
*b Lock


Temporarily install the one-way clutch assembly to the planetary ring gear.


b.

Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

If the one-way clutch assembly does not operate normally, replace it.


Hide 8.INSPECT NO. 1 BRAKE DISC

a.
C203288

Check if the contact surfaces of the discs, plates and flange are worn or burnt.

NOTICE:
·

If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 9.INSPECT NO. 2 BRAKE DISC

a.
C238852

Check if the contact surfaces of the discs, plates and flange are worn or burnt.

NOTICE:
·

If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 10.INSPECT NO. 3 BRAKE DISC

a.
C138255

Check if the contact surfaces of the discs, plates and flanges are worn or burnt.

NOTICE:
·

If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.

·

Before assembling new discs, soak them in ATF for at least 15 minutes.



If necessary, replace them.


Hide 11.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C138254

Using a vernier caliper, measure the free length of the 3 2nd brake piston return springs including the spring seats.

Standard free length:

23.26 mm (0.916 in.)


If the free length is less than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 12.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C141533

Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly together with the spring seat.

Standard free length:

15.79 mm (0.622 in.)


If the free length is less than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 13.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C201505

Using a vernier caliper, measure the free length of the No. 3 brake piston return spring together with the spring seat.

Standard free length:

9.15 mm (0.360 in.)


If the free length is less than the standard free length, replace the No. 3 brake piston return spring sub-assembly.


Hide 14.INSPECT CLEARANCE OF NO. 1 BRAKE

a.
C138258

Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard clearance:

0.601 to 0.819 mm (0.0237 to 0.0322 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.

No. 1 Brake Flange Thickness
Mark Thickness
30 3.0 mm (0.118 in.)
31 3.1 mm (0.122 in.)
32 3.2 mm (0.126 in.)
33 3.3 mm (0.130 in.)
34 3.4 mm (0.134 in.)
35 3.5 mm (0.138 in.)


Hide 15.INSPECT CLEARANCE OF NO. 2 BRAKE

a.
C238856

Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

Standard clearance:

0.707 to 0.974 mm (0.0278 to 0.0383 in.)


HINT:

Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.


If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.

No. 2 Brake Flange Thickness
Mark Thickness
40 4.0 mm (0.157 in.)
41 4.1 mm (0.161 in.)
42 4.2 mm (0.165 in.)
43 4.3 mm (0.169 in.)
44 4.4 mm (0.173 in.)


Hide 16.INSPECT CLEARANCE OF NO. 3 BRAKE

a.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.

C274847
2.333,0.458 2.5,0.208 2.5,0.208 2.625,0.208 false 5.417,0.927 5.563,1.542 5.563,1.542 5.74,1.542 false 6.073,0.625 5.656,0.208 5.656,0.208 5.448,0.208 false 2.667,0.135 2.979,0.292 0.313,0.156 10 *1 5.802,1.479 6.115,1.635 0.313,0.156 10 *2 1.646,0.083 1.958,0.24 0.313,0.156 10 *a 5.708,0.74 6.021,0.896 0.313,0.156 10 *b 5.271,0.115 5.583,0.271 0.313,0.156 10 *c
*1 Front Oil Pump Assembly *2 No. 3 Brake Piston
*a Dimension A *b Dimension B
*c Contact Surface of Front Oil Pump Assembly - -


HINT:

Measure dimension A at 3 points where the flange diameter is approximately 166 mm (6.54 in.) and calculate the average.



b.

Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).

HINT:

Measure dimension B at 3 points where the No. 3 brake diameter is approximately 166 mm (6.54 in.) and calculate the average.



c.

Calculate the clearance value using the following formula:

Clearance = Dimension B - Dimension A - Flange Thickness

Standard clearance:

0.599 to 0.799 mm (0.0236 to 0.0314 in.)


If the clearance is not as specified, select an appropriate No. 3 brake flange so that the clearance will be within the specified range.

No. 3 Brake Flange Thickness
Mark Thickness
38 3.80 mm (0.150 in.)
39 3.90 mm (0.154 in.)
40 4.00 mm (0.157 in.)
41 4.10 mm (0.161 in.)
42 4.20 mm (0.165 in.)
43 4.30 mm (0.169 in.)


Hide 17.INSPECT CLEARANCE OF NO. 1 CLUTCH

a.
C201532

Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.


b.

Check that the piston moves when compressed air (200 kPa, 2.0 kgf/cm2, 29 psi) is applied to the oil hole.


c.
C201533
1.094,0.271 1.198,0.271 1.198,0.271 1.406,1.042 false 0.906,0.177 1.135,0.354 0.229,0.177 10 *a
*a Feeler Gauge


Using a feeler gauge, measure the No. 1 clutch pack clearance.

HINT:

Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.


Standard pack clearance:

0.601 to 0.819 mm (0.0237 to 0.0322 in.)


If the pack clearance is not as specified, replace the direct multiple disc clutch assembly.


Hide 18.INSPECT CLEARANCE OF NO. 2 CLUTCH

a.
C202899

Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.


b.

Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

HINT:

Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.


Pack clearance:

0.394 to 0.605 mm (0.0156 to 0.0238 in.)


If the pack clearance is not as specified, replace the direct multiple disc clutch assembly.