Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP
RM30B0U _52 Drivetrain _010989 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0058572 OIL PUMP A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL FRONT OIL PUMP OIL SEAL

a.
C188149
2.135,2.021 2.625,1.417 2.625,1.417 1.76,0.885 true 2.688,1.333 3.104,1.51 0.417,0.177 10 false SST

Using SST and a hammer, install a new front oil pump oil seal to the front oil pump body sub-assembly.

SST
09350-32014  (09351-32140)

Oil seal driven in depth:

-0.25 to 0.25 mm (-0.00984 to 0.00984 in.)



b.

Coat the lip of the front oil pump oil seal with MP grease.


Hide 2.INSTALL FRONT OIL PUMP BODY O-RING

a.
C138278

Coat a new front oil pump body O-ring with ATF and install it to the front oil pump body sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



Hide 3.INSTALL FRONT OIL PUMP DRIVEN GEAR

a.
C138277

Coat the front oil pump driven gear with ATF and install it to the front oil pump body sub-assembly with the marked side up.


Hide 4.INSTALL FRONT OIL PUMP DRIVE GEAR

a.
C138276

Coat the front oil pump drive gear with ATF, and install it to the front oil pump body sub-assembly with the marked side up.


Hide 5.INSTALL STATOR SHAFT ASSEMBLY

a.
C138275
1.417,2.625 1.563,2.792 0.146,0.167 10 B 0.771,1.198 0.917,1.365 0.146,0.167 10 A 1.031,0.583 1.177,0.75 0.146,0.167 10 A 1.656,0.333 1.802,0.5 0.146,0.167 10 A 2.271,0.531 2.417,0.698 0.146,0.167 10 A 2.583,0.979 2.729,1.146 0.146,0.167 10 A 2.563,1.625 2.708,1.792 0.146,0.167 10 A 2.219,2.115 2.365,2.281 0.146,0.167 10 A 1.729,2.24 1.875,2.406 0.146,0.167 10 A 0.99,1.885 1.125,2.052 0.135,0.167 10 A 2.229,2.802 2.375,2.969 0.146,0.167 10 B 2.438,3.354 2.583,3.521 0.146,0.167 10 B 2.385,4.052 2.531,4.219 0.146,0.167 10 B 0.854,3.823 1,3.99 0.146,0.167 10 B 0.896,3.125 1.042,3.292 0.146,0.167 10 B 1.354,4.26 1.5,4.427 0.146,0.167 10 B

Align each knock pin of the stator shaft assembly with the holes in the front oil pump body sub-assembly and install the stator shaft assembly to the front oil pump body sub-assembly with the 16 bolts.

Bolt Length
Bolt Length
A 14 mm (0.551 in.)
B 26 mm (1.02 in.)


b.

Using a T30 "TORX" socket wrench, tighten the 16 bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)