1.INSPECT TRANSMISSION OIL CLEANER MAGNET
Examine particles in the automatic transaxle oil pan sub-assembly.
Collect any steel chips with the removed magnets. Look carefully at the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.
Bearing, gear and plate wear
Bushing wear
2.INSPECT INPUT SHAFT END PLAY
Using a dial indicator, measure the input shaft end play.
0.020 to 1.242 mm (0.000788 to 0.0488 in.)
3.INSPECT INTERMEDIATE SHAFT END PLAY
| *a | Dimension A |
Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.
As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension A).
| *a | Dimension B |
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
Calculate the end play value using the following formula:
End play = Dimension B - Dimension A - Thrust needle roller bearing thickness
0.022 to 1.099 mm (0.000867 to 0.0432 in.)
4.INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY
Using a caliper gauge, measure the inside diameter of the bushings of the planetary sun gear sub-assembly.
25.525 to 25.546 mm (1.00492 to 1.00574 in.)
25.546 mm (1.00574 in.)
If the inside diameter is more than the maximum, replace the planetary sun gear sub-assemly.
5.INSPECT REAR PLANETARY SUN GEAR ASSEMBLY
Using a caliper gauge, measure the inside diameter of the bushing of the rear planetary sun gear assembly.
25.580 to 25.601 mm (1.00709 to 1.00791 in.)
25.601 mm (1.00791 in.)
If the inside diameter is more than the maximum, replace the automatic transaxle assembly.
6.INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY
Using a feeler gauge, measure the clearance between the underdrive planetary gear assembly and the pinion gear at 4 points.
0.18 to 0.54 mm (0.00709 to 0.0212 in.)
If the clearance is more than the standard clearance, replace the automatic transaxle assembly.
7.INSPECT ONE-WAY CLUTCH ASSEMBLY
| *1 | Planetary Ring Gear |
| *2 | One-way Clutch Assembly |
| *a | Free |
| *b | Lock |
Temporarily install the one-way clutch assembly to the planetary ring gear.
Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.
If the one-way clutch assembly does not operate normally, replace it.
8.INSPECT NO. 1 BRAKE DISC
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
Before assembling new discs, soak them in ATF for at least 15 minutes.
If necessary, replace them.
9.INSPECT NO. 2 BRAKE DISC
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
Before assembling new discs, soak them in ATF for at least 15 minutes.
If necessary, replace them.
10.INSPECT NO. 3 BRAKE DISC
Check if the contact surfaces of the discs, plates and flanges are worn or burnt.
If the lining of any disc is peeled off or discolored, or even if part of the groove is damaged, replace all discs.
Before assembling new discs, soak them in ATF for at least 15 minutes.
If necessary, replace them.
11.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
Using a vernier caliper, measure the free length of the 3 2nd brake piston return springs including the spring seats.
23.26 mm (0.916 in.)
If the free length is less than the standard free length, replace the 2nd brake piston return spring sub-assembly.
12.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly together with the spring seat.
15.79 mm (0.622 in.)
If the free length is less than the standard free length, replace the 1st and reverse brake return spring sub-assembly.
13.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
Using a vernier caliper, measure the free length of the No. 3 brake piston return spring together with the spring seat.
9.15 mm (0.360 in.)
If the free length is less than the standard free length, replace the No. 3 brake piston return spring sub-assembly.
14.INSPECT CLEARANCE OF NO. 1 BRAKE
Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
0.601 to 0.819 mm (0.0237 to 0.0322 in.)
Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.
If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.
| Mark | Thickness |
|---|---|
| 30 | 3.0 mm (0.118 in.) |
| 31 | 3.1 mm (0.122 in.) |
| 32 | 3.2 mm (0.126 in.) |
| 33 | 3.3 mm (0.130 in.) |
| 34 | 3.4 mm (0.134 in.) |
| 35 | 3.5 mm (0.138 in.) |
15.INSPECT CLEARANCE OF NO. 2 BRAKE
Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
0.707 to 0.974 mm (0.0279 to 0.0383 in.)
Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.
If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.
| Mark | Thickness |
|---|---|
| 40 | 4.0 mm (0.157 in.) |
| 41 | 4.1 mm (0.161 in.) |
| 42 | 4.2 mm (0.165 in.) |
| 43 | 4.3 mm (0.169 in.) |
| 44 | 4.4 mm (0.173 in.) |
16.INSPECT CLEARANCE OF NO. 3 BRAKE
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension A) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.
| *1 | Front Oil Pump Assembly | *2 | No. 3 Brake Piston |
| *a | Dimension A | *b | Dimension B |
| *c | Contact Surface of Front Oil Pump Assembly | - | - |
Measure dimension A at 3 points where the flange diameter is approximately 166 mm (6.54 in.) and calculate the average.
Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).
Measure dimension B at 3 points where the No. 3 brake diameter is approximately 166 mm (6.54 in.) and calculate the average.
Calculate the clearance value using the following formula:
Clearance = Dimension B - Dimension A - Flange Thickness
0.599 to 0.799 mm (0.0236 to 0.0314 in.)
If the clearance is not as specified, select an appropriate No. 3 brake flange so that the clearance will be within the specified range.
| Mark | Thickness |
|---|---|
| 38 | 3.80 mm (0.150 in.) |
| 39 | 3.90 mm (0.154 in.) |
| 40 | 4.00 mm (0.157 in.) |
| 41 | 4.10 mm (0.161 in.) |
| 42 | 4.20 mm (0.165 in.) |
| 43 | 4.30 mm (0.169 in.) |
17.INSPECT CLEARANCE OF NO. 1 CLUTCH
Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.
Check that the piston moves when compressed air (200 kPa, 2.0 kgf/cm2, 29 psi) is applied to the oil hole.
| *a | Feeler Gauge |
Using a feeler gauge, measure the No. 1 clutch pack clearance.
Measure the clearance at 3 points where the flange diameter is approximately 152 mm (5.98 in.) and calculate the average.
0.601 to 0.819 mm (0.0237 to 0.0322 in.)
If the pack clearance is not as specified, replace the direct multiple disc clutch assembly.
18.INSPECT CLEARANCE OF NO. 2 CLUTCH
Install the direct multiple disc clutch assembly onto the rear transaxle cover sub-assembly.
Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
Measure the clearance at 3 points where the diameter of the No. 2 direct multiple clutch piston is approximately 152 mm (5.98 in.) and calculate the average.
0.394 to 0.605 mm (0.0156 to 0.0238 in.)
If the pack clearance is not as specified, replace the direct multiple disc clutch assembly.