Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › from 2013.11
RM30B0U _51 Engine / Hybrid System _008971 2AR-FE ENGINE CONTROL _0049217 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0141  Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136

HINT:
·

Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.

·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

A290312
0.125,0.083 2.75,0.25 2.625,0.167 10 Reference (System Diagram of Sensor 2): 5,1 5.615,1.198 0.615,0.198 10 HT1B 5,1.552 5.615,1.75 0.615,0.198 10 OX1B 5,2.083 5.615,2.281 0.615,0.198 10 EX1B 3.344,2.052 4.844,2.25 1.5,0.198 10 Heated Oxygen Sensor 4.469,1.552 5.083,1.75 0.615,0.198 10 OX1B 4.469,1 5.083,1.198 0.615,0.198 10 HT1B 3.771,0.979 4.385,1.177 0.615,0.198 10 Heater 3.76,1.469 4.375,1.667 0.615,0.198 10 Sensor 3.333,1.552 3.583,1.75 0.25,0.198 10 E2 3.333,1 3.583,1.167 0.25,0.167 10 +B 1.063,2.208 1.76,2.375 0.698,0.167 10 EFI NO. 2 0.063,2.052 0.979,2.417 0.917,0.365 10 from EFI-MAIN NO. 1 Relay 0.167,1.135 1,1.333 0.833,0.198 10 from Battery 1.104,1.313 1.802,1.646 0.698,0.333 10 EFI-MAIN NO. 2 5.688,3.302 6.104,3.5 0.417,0.198 10 ECM 1.802,2.385 2.5,2.719 0.698,0.333 10 EFI-MAIN NO. 2



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 2 relay

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) Heated oxygen sensor heater current reaches high limit
(Heater monitor IC high current limiter monitor input "Fail") (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 2 relay

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) The cumulative heater resistance correction value exceeds the threshold (2 trip detection logic).
·

Open or short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 2 relay

·

ECM


Comes on DTC stored DTC for Mexico Models
- Applies
P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored DTC for Mexico Models
- Applies

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037, P0038 and P102D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



Heated Oxygen Sensor Heater Performance (P0141):

After the accumulated heater on time exceeds 100 seconds, the ECM calculates the heater resistance using battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and stores DTC P0141.



MONITOR STRATEGY

Related DTCs P0037: Heated oxygen sensor heater (sensor 2) range check (low current)
P0038: Heated oxygen sensor heater (sensor 2) range check (high current)
P0141: Heated oxygen sensor heater performance (sensor 2)
P102D: Heated oxygen sensor heater performance (sensor 2)
Required Sensors/Components (Main) Heated oxygen sensor heater (sensor 2)
Required Sensors/Components (Related) -
Frequency of Operation Continuous: P0037, P0038, P102D
Once per driving cycle: P0141
Duration 0.5 seconds: P0037
Within 3 seconds: P0038
10 seconds: P0141
0.5 seconds: P102D
MIL Operation Immediate: P0037, P0038, P102D
2 driving cycles: P0141
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever the following DTCs are not stored None

P0037: (Case 1)
All of the following conditions are met -
Battery voltage 10.5 V or higher
Engine Running
Starter Off
Catalyst active A/F control Not operating
Time after heater on 10 seconds or more
Learned heater off current operation Completed
Learned heater off current operation Succeeded
Oxygen sensor heater high current fail (P0038) Not detected
Heater on current - Learned heater off current 0.15 A or less
Heater output On

P0037: (Case 2)
All of the following conditions are met -
Battery voltage 10.5 V or higher
Engine Running
Starter Off
Catalyst active A/F control Not operating
Time after heater on 10 seconds or more
Learned heater off current operation Completed
Oxygen sensor heater high current fail (P0038) Not detected
Heater off current Higher than 3.5 A
Heater monitor IC high current limiter monitor input Fail

P0038
All of the following conditions are met -
Battery voltage 10.5 V or higher
Engine Running
Starter Off
Catalyst active A/F control Not operating
Time after heater on 10 seconds or more
Learned heater off current operation Completed
Heater monitor IC high current limiter monitor input Fail
Heater output On

P0141
All of the following conditions are met -
Heated oxygen sensor heater circuit fail (P0037, P0038 and P102D) Not detected
Battery voltage 10.5 V or higher
Fuel cut Off
Time after fuel cut on to off 30 seconds or more
Accumulated heater on time 100 seconds or more
Learned heater off current operation Completed
Duration that heated oxygen sensor impedance is less than 15 kΩ 2 seconds or more

P102D
All of the following conditions are met -
Battery voltage 10.5 V or higher
Engine Running
Starter Off
Catalyst active A/F control Not operating
Time after heater on 10 seconds or more
Learned heater off current operation Completed
Oxygen sensor heater low current fail (P0037) Not detected
Oxygen sensor heater high current fail (P0038) Not detected
Heater output Off
Heater off current Higher than 3.5 A
Heater monitor IC high current limiter monitor input Fail

TYPICAL MALFUNCTION THRESHOLDS

P0037: (Case 1)
Heater on current - Learned heater off current 0.15 A or less

P0037: (Case 2)
Heater on current 1 A or less

P0038
Both of the following conditions are met -
Heater monitor IC high current limiter monitor input Fail
Heater output On

P0141
Heater resistance Varies with sensor element temperature (Example: Higher than 23 Ω)

P102D
Heater on current Higher than 1 A

MONITOR RESULT

Refer to detailed information in Checking Monitor Status.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>CHECKING MONITOR STATUS

P0141: O2 Sensor Heater / O2 HEATER B1S2
Monitor ID Test ID Scaling Unit Description
$42 $91 Multiply by 0.001 Ohm Oxygen sensor heater resistance bank 1 sensor 2

CONFIRMATION DRIVING PATTERN

A262623
0.792,0.969 1.438,1.167 0.646,0.198 10 3000 rpm 1.031,1.74 1.417,1.99 0.385,0.25 10 Idling 0.229,2.01 1.396,2.354 1.167,0.344 10 Ignition Switch ON 1.927,2.135 2.198,2.396 0.271,0.26 10 [A] 2.76,1.625 2.979,1.927 0.219,0.302 10 [B] 4.021,0.865 4.302,1.135 0.281,0.271 10 [C] 5.385,1.604 5.615,1.885 0.229,0.281 10 [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 5 minutes or more 3.854,2.615 4.427,2.781 0.573,0.167 10 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 [E]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037, P0038, P0141 or P102D.

13.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.



14.

If no pending DTC is output, perform a universal trip and check for permanent DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A299798
5.417,0.573 5.719,0.74 0.302,0.167 10 false B77 5.417,1.344 5.719,1.51 0.302,0.167 10 false B77 5.417,2.021 5.719,2.188 0.302,0.167 10 false B77 5.417,3.031 5.719,3.198 0.302,0.167 10 false A62 5.469,0.396 5.719,0.563 0.25,0.167 10 false 24 5.75,0.479 6.167,0.646 0.417,0.167 10 false HT1B 5.427,1.177 5.729,1.344 0.302,0.167 10 false 100 5.75,1.25 6.135,1.417 0.385,0.167 10 false OX1B 5.417,1.854 5.719,2.021 0.302,0.167 10 false 132 5.75,2.01 6.167,2.177 0.417,0.167 10 false EX1B 5.458,2.865 5.708,3.031 0.25,0.167 10 false 46 5.75,3.01 6.167,3.177 0.417,0.167 10 false MREL 6.167,4 6.5,4.167 0.333,0.167 10 false ECM 3.417,1.5 3.719,1.667 0.302,0.167 10 false B25 3.417,1.667 4.917,1.917 1.5,0.25 10 false Heated Oxygen Sensor 3.781,1.188 4,1.354 0.219,0.167 10 false E2 4.188,1.177 4.604,1.344 0.417,0.167 10 false OX1B 4.698,1.25 5,1.417 0.302,0.167 10 false 3 3.563,1.25 3.729,1.417 0.167,0.167 10 false 4 3.563,0.479 3.729,0.646 0.167,0.167 10 false 2 3.771,0.479 3.99,0.646 0.219,0.167 10 false +B 4.198,0.469 4.615,0.635 0.417,0.167 10 false HT1B 4.698,0.479 5,0.646 0.302,0.167 10 false 1 2.583,0.469 2.75,0.635 0.167,0.167 10 false 3 1.76,0.469 1.896,0.635 0.135,0.167 10 false 5 1.75,0.75 1.885,0.917 0.135,0.167 10 false 1 2.583,0.74 2.719,0.906 0.135,0.167 10 false 2 1.698,1.177 2.75,1.344 1.052,0.167 10 false EFI-MAIN NO. 2 1.729,1.677 2.448,1.844 0.719,0.167 10 false EFI NO. 2 1.781,3.365 2.833,3.531 1.052,0.167 10 false EFI-MAIN NO. 1 2.531,2.656 2.667,2.823 0.135,0.167 10 false 3 2.531,2.948 2.667,3.115 0.135,0.167 10 false 1 1.792,2.948 1.927,3.115 0.135,0.167 10 false 2 1.792,2.656 1.958,2.823 0.167,0.167 10 false 5 0.604,3.219 1.188,3.385 0.583,0.167 10 false FL MAIN 0.75,3.958 1.25,4.208 0.5,0.25 10 false Battery 0.583,0.698 1.667,0.865 1.083,0.167 10 false EFI-MAIN NO. 2 0.583,2.875 1.583,3.042 1,0.167 10 false EFI-MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2].

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click here Engine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
a.
A149595
0.5,1.833 0.917,2.083 0.417,0.25 1.948,1.833 2.365,1.417 false 0.083,0.083 0.344,0.281 0.26,0.198 10 *a 0.604,1.875 0.917,2.083 0.313,0.208 10 B25 2.417,1.333 2.667,1.5 0.25,0.167 10 +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B25-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.INSPECT EFI-MAIN NO. 2 RELAY
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-1 (HT1B) - B77-24 (HT1B) Always Below 1 Ω
B25-1 (HT1B) or B77-24 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0141 OR P102D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0141 OR P102D)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0037, P0038, P0141 or P102D is output B




A

B

5.INSPECT EFI-MAIN NO. 2 RELAY
a.

Inspect the EFI-MAIN No. 2 relay.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - HEATED OXYGEN SENSOR, EFI-MAIN NO. 1 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - HEATED OXYGEN SENSOR, EFI-MAIN NO. 1 RELAY)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


c.

Disconnect the heated oxygen sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI-MAIN NO. 2 relay terminal 3 - B25-2 (+B) Always Below 1 Ω
EFI-MAIN NO. 2 relay terminal 1 - EFI-MAIN NO. 1 relay terminal 3 Always Below 1 Ω
EFI-MAIN NO. 2 relay terminal 2 - Body ground Always Below 1 Ω
EFI-MAIN NO. 2 relay terminal 3 or B25-2 (+B) - Body ground Always 10 kΩ or higher
EFI-MAIN NO. 2 relay terminal 1 or EFI-MAIN NO. 1 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)