Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › from 2013.11
RM30B0U _52 Drivetrain _009030 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0049436 AUTOMATIC TRANSAXLE SYSTEM C

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

Refer to DTC P0711.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>P0711

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
·

Short in ATF temperature sensor circuit

·

ATF temperature sensor (transmission wire)

·

Wiring harness connector

·

ECM


Comes on DTC stored
P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more and either condition is met (1-trip detection logic):
(A) 426 sec. or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.
(B) 10 sec. or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (- 20.875°F).
·

Open in ATF temperature sensor circuit

·

ATF temperature sensor (transmission wire)

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the ATF temperature sensor circuit. The ATF temperature sensor converts ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is below 79 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM will turn on the MIL and store the DTC.

HINT:
·

The ATF temperature can be checked on the Techstream display.

·

*1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.

·

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.



MONITOR STRATEGY

Related DTCs P0712: ATF temperature sensor/Range check (Low voltage)
P0713: ATF temperature sensor/Range check (High voltage)
Required sensors/Components ATF temperature sensor
Frequency of operation Continuous
Duration 0.5 sec.
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

P0712: Range Check (Low Voltage)
The monitor will run whenever the following DTCs are not stored None
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF


P0713: Range Check (High Voltage)

Either condition is met: Condition (A) or (B)

Condition (A)
The monitor will run whenever the following DTCs are not stored P0115, P0117, P0118 (ECT (Engine Coolant Temperature) sensor circuit)
P00AC, P00AD, P0110, P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF
Engine coolant temperature or intake air temperature at engine start -29.375°C (-20.875°F) or less
Time after engine start 426 sec. or more
ECT sensor circuit fail (P0115, P0117, P0118) Not detected
IAT sensor circuit fail (P00AC, P00AD, P0110, P0112, P0113) Not detected

Condition (B)
The monitor will run whenever the following DTCs are not stored P0115, P0117, P0118 (ECT (Engine Coolant Temperature) sensor circuit)
P00AC, P00AD, P0110, P0112, P0113 (IAT (Intake Air Temperature) sensor circuit)
Battery voltage 8 V or higher
Ignition switch ON
Starter OFF
Engine coolant temperature and intake air temperature at engine start Higher than -29.375°C (-20.875°F)
Time after engine start 10 sec. or more
ECT sensor circuit fail (P0115, P0117, P0118) Not detected
IAT sensor circuit fail (P00AC, P00AD, P0110, P0112, P0113) Not detected


TYPICAL MALFUNCTION THRESHOLDS

P0712: Range Check (Low Voltage)
ATF temperature sensor voltage Below 0.14 V (Higher than 164°C (327.2°F))

P0713: Range Check (High Voltage)
ATF temperature sensor voltage Higher than 4.91 V (Below -48°C (-54.4°F))

COMPONENT OPERATING RANGE

ATF temperature sensor voltage 0.14 to 4.91 V

WIRING DIAGRAM

C240445
5.833,4.292 6.479,4.479 0.646,0.188 10 false ECM 5.323,1.396 5.865,1.563 0.542,0.167 10 false THO1 0.667,2.927 2.313,3.292 1.646,0.365 10 false ATF Temperature Sensor 3.802,1.198 4.344,1.365 0.542,0.167 10 false 13 3.802,2.333 4.344,2.5 0.542,0.167 10 false 12 5.823,4.125 6.365,4.292 0.542,0.167 10 false B77 2.531,2.333 3.073,2.5 0.542,0.167 10 false 17 2.521,1.219 3.063,1.385 0.542,0.167 10 false 18 5.313,2.531 5.854,2.698 0.542,0.167 10 false ETHO 4.99,2.656 5.531,2.823 0.542,0.167 10 false 119 4.99,1.531 5.531,1.698 0.542,0.167 10 false 120 0.865,3.396 2.219,3.583 1.354,0.188 10 false Transmission Wire 2.802,3.406 3.802,3.76 1,0.354 10 false Wiring Harness Connector 3.74,1.406 4.156,1.563 0.417,0.156 10 false B78 3.75,2.531 4.031,2.688 0.281,0.156 10 false B78 2.563,1.417 2.844,1.573 0.281,0.156 10 false A 2.573,2.542 2.854,2.698 0.281,0.156 10 false A 1.969,1.271 2.448,1.458 0.479,0.188 10 false THO1 2.031,2.427 2.344,2.594 0.313,0.167 10 false E2 3.417,1.281 3.958,1.448 0.542,0.167 10 false OIL 3.448,2.427 3.781,2.594 0.333,0.167 10 false E2

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION

·


DATA LIST


HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the Techstream, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

After stall test: Approx. 80°C (176°F)

·

Equal to ambient temperature after cold soak


If the value is "-40°C (-40°F)" or "150°C (302°F)", the ATF temperature sensor circuit is open or shorted.
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406
HINT:

When DTC P0712 is output and the Techstream indicates 150°C (302°F) or higher, there is a short circuit.

When DTC P0713 is output and the Techstream indicates -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the Techstream in order to check if a malfunction exists.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit

If the circuit related to the ATF temperature sensor becomes open, P0713 is immediately stored (in 0.5 seconds). When P0713 is stored, P0711 cannot be stored.

It is not necessary to inspect the circuit when P0711 is stored.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR CIRCUIT)
a.
C267934
1.448,0.177 1.865,0.385 0.417,0.208 0.719,1.74 1.115,1.146 true 1.646,1.74 1.188,1.146 true 1.531,0.208 1.99,0.406 0.458,0.198 10 false B77 0.302,1.802 1.198,2 0.896,0.198 10 false 119 (ETHO) 1.354,1.802 2.313,1.99 0.958,0.188 10 false 120 (THO1) 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-120 (THO1) - B77-119 (ETHO) Always 79 Ω to 156 kΩ
B77-120 (THO1) - Body ground and other terminals Always 10 kΩ or higher
B77-119 (ETHO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
a.

Disconnect the B78 wiring harness connector.


b.

Disconnect the B77 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-13 (OIL) - B77-120 (THO1) Always Below 1 Ω
B78-12 (E2) - B77-119 (ETHO) Always Below 1 Ω
B78-13 (OIL) or B77-120 (THO1) - Body ground and other terminals Always 10 kΩ or higher
B78-12 (E2) or B77-119 (ETHO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ATF TEMPERATURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ATF TEMPERATURE SENSOR
a.
C226545
0.594,0.76 0.938,1 0.344,0.24 1.677,1.51 1.885,1.135 true 2.167,1.51 2,1.135 true 0.354,0.219 0.667,0.417 0.313,0.198 10 *a 1.469,1.552 2.083,1.75 0.615,0.198 10 THO1 2.115,1.552 2.729,1.75 0.615,0.198 10 E2 0.708,0.792 1.063,0.99 0.354,0.198 10 A
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-18 (THO1) - A-17 (E2) Always 79 Ω to 156 kΩ
A-18 (THO1) - Body ground and other terminals Always 10 kΩ or higher
A-17 (E2) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.


ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ


Result:
Proceed to
OK
NG



OK

NG

REPLACE ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)