Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY › from 2013.11
RM30B0U _52 Drivetrain _009983 GF1A TRANSFER / 4WD / AWD _0060052 TRANSFER ASSEMBLY A

GF1A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Before installation of each part, thoroughly clean and dry it. Then apply grease or oil as necessary. Do not use alkaline chemicals to clean aluminum parts, rubber parts or precoated bolts. Also, do not use non-residue solvent or other cleaning oils to clean O-rings, oil seals or rubber parts.


PROCEDURE

Hide 1.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.
C278970

Using 2 nuts, remove the 4 transfer and transaxle setting stud bolts.


Hide 2.SECURE TRANSFER ASSEMBLY

C284178

a.

Secure the transfer assembly to the overhaul attachment.


Hide 3.REMOVE TRANSFER CASE STRAIGHT PIN

C284179

a.

Remove the 2 transfer case straight pins.


Hide 4.REMOVE NO. 1 TRANSFER CASE PLUG

C130044

a.

Remove the No. 1 transfer case plug and gasket.


Hide 5.REMOVE TRANSFER DRAIN PLUG

C284180

a.

Using a 10 mm socket hexagon wrench, remove the transfer drain plug and gasket.


Hide 6.REMOVE NO. 2 TRANSFER CASE PLUG

C284181

a.

Using a 10 mm socket hexagon wrench, remove the No. 2 transfer case plug (filler plug) and gasket.


Hide 7.REMOVE TRANSFER CASE BREATHER PLUG

C222931

a.

Using a chisel and hammer, slightly pry out the transfer case breather plug.


b.

Using a screwdriver, lightly pry up and remove the transfer case breather plug.


Hide 8.REMOVE TRANSFER CASE OIL SEAL

C278965
0.667,0.708 0.833,0.708 0.833,0.708 1.083,0.292 true 1.99,1.823 2.146,1.823 2.146,1.823 2.396,1.125 true 0.469,0.615 0.781,0.771 0.313,0.156 10 false *1 1.677,1.75 2.094,1.917 0.417,0.167 10 false SST
*1 Transfer Case Oil Seal


a.

Using SST, remove the transfer case oil seal from the transfer case.

SST
09308-00010  

NOTICE:

Do not scratch the press-fitting surface of the transfer case oil seal.



Hide 9.REMOVE TRANSFER CASE OIL SEAL RH

C130055
1.875,1.188 1.75,1.802 1.75,1.802 1.615,1.802 false 0.771,0.354 0.583,0.625 0.583,0.625 0.438,0.625 true 1.323,1.729 1.729,1.948 0.406,0.219 10 SST 0.281,0.542 0.635,0.76 0.354,0.219 10 *1
*1 Transfer Case Oil Seal RH


a.

Using SST, remove the transfer case oil seal RH from the No. 1 transfer case cover.

SST
09308-00010  

NOTICE:

Do not scratch the press-fitting surface of the transfer case oil seal RH.



Hide 10.INSPECT TOTAL PRELOAD

C130167
2.417,0.667 2.031,0.667 false 2.469,0.594 2.781,0.75 0.313,0.156 10 *1 0.167,0.177 0.625,0.375 0.458,0.198 10 90°
*1 Nut


a.

Install nuts to the stud bolts.

HINT:

Use nuts that are used for installing the propeller shaft.



b.

Using a torque wrench, check the total preload (starting torque) with the teeth of the drive pinion and ring gear in contact.

Torque:
Total preload (starting torque) : 0.47 to 2.2 N*m (4.80 to 22.43 kgf*cm, 4.16 to 19.47 in.*lbf)

HINT:

Install the torque wrench as shown in the illustration.



Hide 11.INSPECT RING GEAR BACKLASH

C158062

a.

Insert a dial indicator through the No. 2 transfer case plug hole, and set it perpendicular to the edge of a ring gear tooth.

If the backlash is not within the specified range, adjust the backlash or repair as necessary.


b.

While securing the transfer output shaft by hand, rotate the transfer ring gear mounting case forward and backward by hand and measure the backlash of the ring gear and driven pinion.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


NOTICE:

Measure the ring gear at 3 or more locations.



Hide 12.REMOVE NO. 1 TRANSFER CASE COVER

a.
C130048

Remove the 8 bolts.


b.
C130049

Using a brass bar and hammer, remove the No. 1 transfer case cover from the transfer case.

NOTICE:
·

Put the brass bar against the rib of the No. 1 transfer case cover.

·

When removing the No. 1 transfer case cover, be careful not to scratch the installation surface.



HINT:

To prevent the No. 1 transfer case cover from falling, leave 2 of the bolts screwed in by 5 or 6 threads.



Hide 13.REMOVE TRANSFER RING GEAR

C130050

a.

Remove the transfer ring gear from the transfer case.


Hide 14.REMOVE TRANSFER CASE STRAIGHT PIN

C130051

a.

Remove the 2 transfer case straight pins from the transfer case.


Hide 15.INSPECT DRIVEN PINION PRELOAD

a.
C130052
2.479,0.656 2.031,0.656 false 2.531,0.583 2.844,0.74 0.313,0.156 10 *1 0.146,0.115 0.458,0.271 0.313,0.156 10 90°
*1 Nut


Install nuts to the stud bolts.

HINT:

Use nuts that are used for installing the propeller shaft.



b.

Using a torque wrench, check the driven pinion preload (starting torque) of the driven pinion.

Torque:
Driven pinion preload (starting torque) : 0.24 to 1.39 N*m (2.45 to 14.17 kgf*cm, 2.13 to 12.30 in.*lbf)

HINT:

Install the torque wrench as shown in the illustration.



Hide 16.REMOVE REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

C130053

a.

Remove the 5 bolts and rear transfer output shaft sub-assembly from the transfer case.


b.

Mount the rear transfer output shaft sub-assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C130056
1.094,1.094 1.219,1.094 1.219,1.094 1.406,0.896 false 0.802,1.042 1.26,1.24 0.458,0.198 10 SST

Using SST and a hammer, unstake the transfer gear nut.

SST
09930-00010  

NOTICE:
·

Be sure to use SST with the tapered surface facing the shaft.

·

Do not grind the tip of SST with a grinder or other device.

·

Completely loosen the staked part of the transfer gear nut when removing it.

·

Do not damage the threads of the output shaft sub-assembly.




d.

Using a 30 mm socket wrench, remove the transfer gear nut.


Hide 17.REMOVE TRANSFER DRIVEN PINION

C109627
2.313,0.479 2.458,0.479 2.458,0.479 2.76,0.844 true 2.74,1.01 2.458,0.479 true 2.51,1.052 2.448,0.479 true 1.917,0.448 2.26,0.615 0.344,0.167 10 SST

a.

Using SST and a press, remove the transfer driven pinion from the rear transfer output shaft sub-assembly.

SST
09950-00020  
09950-60010  (09951-00240)
09950-70010  (09951-07100)

NOTICE:

Support the front transfer driven pinion bearing as shown in the illustration to avoid placing stress on the outer race.



Hide 18.REMOVE REAR TRANSFER OUTPUT SHAFT DUST DEFLECTOR

a.
C109629
2.365,0.563 2.25,0.563 2.25,0.563 2,1.021 false 2.406,0.49 2.729,0.667 0.323,0.177 10 SST

Using SST and a press, remove the rear transfer output shaft dust deflector from the rear transfer output shaft sub-assembly.

SST
09950-00020  


Hide 19.REMOVE FRONT TRANSFER DRIVEN PINION BEARING

C109628
1.859,0.496 2.2,0.661 0.341,0.166 10 SST 2.26,0.599 2.724,0.599 false 2.26,0.599 2.595,1.064 false 2.26,0.599 2.326,1.035 false

a.

Using SST and a press, remove the front transfer driven pinion bearing from the transfer driven pinion.

SST
09950-00020  
09950-60010  (09951-00410)
09950-70010  (09951-07100)

NOTICE:

Support the front transfer driven pinion bearing as shown in the illustration to avoid placing stress on the outer race.



b.
C109630

Remove the O-ring from the front transfer driven pinion bearing.


Hide 20.REMOVE TRANSFER OUTPUT SHAFT WASHER

C110759

a.

Remove the transfer output shaft washer from the transfer driven pinion.


Hide 21.REMOVE RING GEAR MOUNTING CASE BEARING RH

C269126
2.563,1.51 2.844,1.896 true 2.365,1.563 2.844,1.896 2.844,1.896 3.031,1.896 true 3.052,0.5 3.365,0.656 0.313,0.156 10 *a 1.531,1.021 1.844,1.177 0.313,0.156 10 *b 3.083,1.781 3.427,1.979 0.344,0.198 10 SST
*a Turn
*b Hold


a.

Using SST, remove the ring gear mounting case bearing RH (inner race) from the transfer ring gear mounting case.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00540)

NOTICE:
·

Apply a lubricant to the threads and end of SST.

·

Do not deform the cage of the ring gear mounting case bearing RH (inner race) (when reusing the bearing).

·

Place identification marks on the left and right ring gear mounting case bearings to distinguish them (backside, teeth side). Then store them separately (when reusing the bearings).




b.
C156143
2.156,0.979 2.531,0.979 false 0.573,0.688 0.573,1.469 0.573,1.469 0.854,1.469 true 0.927,1.198 0.75,1.198 0.75,1.198 0.75,0.594 true 0.958,1.104 1.229,1.281 0.271,0.177 10 *1 0.896,1.385 1.167,1.542 0.271,0.156 10 *2 2.552,0.906 3.063,1.219 0.51,0.313 10 SST
*1 No. 2 Transfer Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing RH (Outer Race)


Using SST and a hammer, remove the No. 2 transfer ring gear mounting case washer and ring gear mounting case bearing RH (outer race) from the No. 1 transfer case cover.

SST
09310-35010  


Hide 22.REMOVE RING GEAR MOUNTING CASE BEARING LH

C269127
0.583,1.729 0.719,1.729 0.719,1.729 0.969,1.552 true 1.042,1.167 0.698,1.729 true 0.229,1.625 0.688,1.823 0.458,0.198 10 SST 2.76,0.271 3.073,0.427 0.313,0.156 10 *a 0.365,0.76 0.677,0.917 0.313,0.156 10 *b
*a Turn
*b Hold


a.

Using SST, remove the ring gear mounting case bearing LH (inner race) from the transfer ring gear mounting case.

SST
09950-00020  
09950-00030  

NOTICE:
·

Apply a lubricant to the threads and end of SST.

·

Do not deform the cage of the ring gear mounting case bearing LH (inner race) (when reusing the bearing).

·

Place identification marks on the left and right ring gear mounting case bearings to distinguish them (backside, teeth side). Then store them separately (when reusing the bearings).




b.
C284182
1.333,1.865 1.167,1.865 1.167,1.865 1.167,0.969 true 0.646,1.656 0.479,1.656 0.479,1.656 0.479,1.083 true 1.385,1.802 1.698,1.958 0.313,0.156 10 false *1 0.698,1.563 1.01,1.719 0.313,0.156 10 false *2
*1 No. 1 Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing LH (Outer Race)


Using SST and a hammer, remove the No. 1 ring gear mounting case washer and ring gear mounting case bearing LH (outer race) from the transfer case.

SST
09636-20010  


Hide 23.REMOVE SHAFT SNAP RING

C109636

a.

Using a snap ring expander, remove the shaft snap ring.


Hide 24.REMOVE TRANSFER RING GEAR MOUNTING CASE

C109637
1.906,0.406 2.115,0.406 false 2.135,0.333 2.615,0.563 0.479,0.229 10 SST

a.

Using SST and a press, remove the transfer ring gear mounting case from the transfer ring gear.

SST
09950-60010  (09951-00400)


Hide 25.REMOVE BREATHER OIL DEFLECTOR

C284183

a.

Remove the 2 bolts and breather oil deflector from the transfer case.