Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY › from 2013.11
RM30B0U _52 Drivetrain _009983 GF1A TRANSFER / 4WD / AWD _0060052 TRANSFER ASSEMBLY A

GF1A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Steps 9 to 16 are temporary reassembly procedures for adjustment purposes.


PROCEDURE

Hide 1.INSTALL BREATHER OIL DEFLECTOR

C284183

a.

Install a new breather oil deflector to the transfer case with the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 2.INSTALL TRANSFER RING GEAR MOUNTING CASE

C130226
0.906,0.729 0.75,0.417 0.75,0.417 0.667,0.417 true 1.031,1.302 1.24,1.833 1.24,1.833 1.333,1.833 true 0.365,0.354 0.698,0.5 0.333,0.146 10 SST 1.365,1.75 1.677,1.917 0.313,0.167 10 SST

a.

Using SST and a press, press the transfer ring gear mounting case into the transfer ring gear.

SST
09316-12010  
09950-60010  (09951-00560)

NOTICE:

Do not put stress on the teeth of the transfer ring gear.



Hide 3.INSTALL SHAFT SNAP RING

C109636

a.

Using a snap ring expander, install a new shaft snap ring.


Hide 4.INSTALL RING GEAR MOUNTING CASE BEARING RH

a.
C156148
1.333,0.667 1.167,1.469 true 1.271,1.563 1.271,2.167 1.271,2.167 1.396,2.167 true 0.333,1.917 0.417,1.917 0.417,1.917 0.594,1.469 true 1,1.333 1.333,0.667 true 0.917,1.083 1.333,0.667 1.333,0.667 1.417,0.667 true 1.49,0.583 2,0.844 0.51,0.26 10 false SST 1.427,2.094 1.833,2.333 0.406,0.24 10 false *1 0.135,1.833 0.333,2 0.198,0.167 10 false *2
*1 No. 2 Transfer Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing RH (Outer Race)


Install a new No. 2 transfer ring gear mounting case washer to the No. 1 transfer case cover.

HINT:

Install a No. 2 transfer ring gear mounting case washer with the same thickness as the one before the disassembly.



b.

Using SST and a press, press the ring gear mounting case bearing RH (outer race) into the No. 1 transfer case cover.

SST
09950-60020  (09951-00750, 09952-06010)
09950-70010  (09951-07150)
09951-00850  

NOTICE:
·

Press in the ring gear mounting case bearing RH (outer race) and No. 2 transfer ring gear mounting case washer until they fit to the edge.

·

Do not put stress on the rolling contact surface of the ring gear mounting case bearing RH (outer race).




c.
C130227
0.75,0.333 0.833,0.333 0.833,0.333 1.083,0.583 true 1.083,1.688 1.5,2 1.5,2 1.583,2 true 0.417,0.25 0.875,0.448 0.458,0.198 10 SST 1.625,1.917 2.083,2.115 0.458,0.198 10 SST

Using SST and a press, press the ring gear mounting case bearing RH (inner race) into the transfer ring gear mounting case.

SST
09950-60010  (09951-00440, 09951-00650)

NOTICE:

Do not deform the ring gear mounting case bearing RH (inner race) cage.


HINT:

When reusing the ring gear mounting case bearing RH, coat the ring gear mounting case bearing RH with Toyota Genuine Differential gear oil LT API GL-5 or equivalent.



Hide 5.INSTALL RING GEAR MOUNTING CASE BEARING LH

a.
C156149
1.052,1.542 1.052,2.146 1.052,2.146 1.135,2.146 true 0.656,1.479 0.406,2.063 0.406,2.063 0.323,2.063 true 1.25,0.917 0.917,1.333 true 1.25,0.917 1,1.417 true 1.333,0.917 1.25,0.917 1.25,0.917 0.917,1.167 true 1.188,2.063 1.656,2.302 0.469,0.24 10 *1 0.167,1.99 0.563,2.24 0.396,0.25 10 *2 1.427,0.833 2,1.052 0.573,0.219 10 SST
*1 No. 1 Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing LH (Outer Race)


Install a new No. 1 ring gear mounting case washer to the transfer case.

HINT:

Install a No. 1 ring gear mounting case washer with the same thickness as the one before the disassembly.



b.

Using SST and a press, press the ring gear mounting case bearing LH (outer race) into the transfer case.

SST
09950-60010  (09951-00570, 09951-00650, 09952-06010)
09950-70010  (09951-07150)

NOTICE:
·

Press in the ring gear mounting case bearing LH (outer race) and No. 1 ring gear mounting case washer until they fit to the edge.

·

Do not put stress on the rolling contact surface of the ring gear mounting case bearing LH (outer race).




c.
C130228
2.917,0.333 2.833,0.333 2.833,0.333 2.667,0.531 true 3,1.25 2.917,1.25 2.917,1.25 2.833,1.5 true 2.948,0.271 3.333,0.5 0.385,0.229 10 SST 3.031,1.177 3.365,1.333 0.333,0.156 10 SST

Using SST and a press, press the ring gear mounting case bearing LH (inner race) into the transfer ring gear mounting case.

SST
09336-16010  
09950-60010  (09951-00560)

NOTICE:

Do not deform the ring gear mounting case bearing LH (inner race) cage.


HINT:

When reusing the ring gear mounting case bearing LH, coat the ring gear mounting case bearing LH with Toyota Genuine Differential gear oil LT API GL-5 or equivalent.



Hide 6.INSTALL TRANSFER OUTPUT SHAFT WASHER

C110759

a.

Install the transfer output shaft washer to the transfer driven pinion.


Hide 7.INSTALL FRONT TRANSFER DRIVEN PINION BEARING

C291235
0.969,0.448 1.26,0.292 1.26,0.292 1.021,0.729 true 0.5,1.74 0.656,1.74 0.656,1.74 0.813,1.625 true 1.365,0.208 1.823,0.406 0.458,0.198 10 false SST 0.198,1.677 0.656,1.875 0.458,0.198 10 false SST

a.

Using SST and a press, press the front transfer driven pinion bearing into the transfer driven pinion.

SST
09950-60010  (09951-00440, 09951-00550)
09950-70010  (09951-07150)

NOTICE:

Do not apply stress to any parts of the front transfer driven pinion bearing inner race or transfer driven pinion other than the flat surfaces.



Hide 8.INSTALL REAR TRANSFER OUTPUT SHAFT DUST DEFLECTOR

a.
C293257
0.844,0.719 1.094,0.302 1.094,0.302 1.26,0.302 true 1.198,1.104 1.198,1.604 1.198,1.604 1.313,1.604 true 1.375,0.24 1.833,0.438 0.458,0.198 10 false SST 1.396,1.521 1.854,1.719 0.458,0.198 10 false SST

Using SST and a press, press a new rear transfer output shaft dust deflector into the rear transfer output shaft sub-assembly.

SST
09316-12010  
09950-60010  (09951-00570)

NOTICE:

The rear transfer output shaft dust deflector should be installed completely.



Hide 9.INSTALL TRANSFER DRIVEN PINION

C277112
1.25,1.698 1.25,1.5 1.25,1.5 1.417,1.5 true 1.167,0.458 1.167,0.167 1.167,0.167 1.333,0.167 true 1.458,0.083 1.917,0.281 0.458,0.198 10 SST 1.5,1.417 1.958,1.615 0.458,0.198 10 SST

a.

Using SST and a press, press the transfer driven pinion into the rear transfer output shaft sub-assembly.

SST
09506-30012  
09950-60020  (09951-00680)

NOTICE:

Do not apply stress to any parts of the transfer output shaft flange or transfer driven pinion other than the flat surfaces.



b.

Secure the rear transfer output shaft sub-assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C132102

Using a 30 mm socket wrench, install a new transfer gear nut to the rear transfer output shaft sub-assembly.

Torque:
360 N*m (3671 kgf*cm, 266 ft.*lbf)


Hide 10.INSTALL REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

a.
C156150
2.438,1.406 2.438,1.156 2.438,1.156 2.521,1.156 false 2.542,1.073 2.854,1.229 0.313,0.156 10 *1
*1 O-ring


Install a new O-ring to the front transfer driven pinion bearing.

NOTICE:
·

Do not scratch or twist the O-ring.

·

Firmly install the O-ring into the groove of the front transfer driven pinion bearing.




b.
C130053

Install the rear transfer output shaft sub-assembly to the transfer case with the 5 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Do not scratch or twist the O-ring.



Hide 11.INSPECT DRIVEN PINION PRELOAD

C130052
2.479,0.656 2.031,0.656 false 2.531,0.583 2.844,0.74 0.313,0.156 10 *1 0.146,0.115 0.458,0.271 0.313,0.156 10 90°
*1 Nut


a.

Install a nut to the stud bolt.

HINT:

Use a nut that is used for installing the propeller shaft.



b.

Using a torque wrench, check the driven pinion preload (starting torque) of the driven pinion.

Driven pinion preload (starting torque):
Item Specified Condition
New bearing 0.28 to 2.04 N*m (2.86 to 20.80 kgf*cm, 2.48 to 18.05 in.*lbf)
Reused bearing 0.24 to 1.39 N*m (2.45 to 14.17 kgf*cm, 2.13 to 12.30 in.*lbf)


NOTICE:

Measure the preload after rotating the bearing several times in the forward and backward directions to make sure the bearing is operating correctly.


HINT:

Install the torque wrench as shown in the illustration.



Hide 12.INSTALL TRANSFER RING GEAR

C110563

a.

Uniformly apply a light coat of Prussian Blue on both sides of the transfer ring gear teeth.


b.
C130050

Install the transfer ring gear to the transfer case.


Hide 13.INSTALL NO. 1 TRANSFER CASE COVER

C130048

a.

Install the No. 1 transfer case cover to the transfer case with the 8 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 14.ADJUST RING GEAR BACKLASH

a.
C158062

Insert a dial indicator into the No. 2 transfer case plug hole, and place it perpendicular to the edge of a transfer ring gear tooth.


b.

While securing the rear transfer output shaft sub-assembly by hand, rotate the transfer ring gear mounting case forward and backward by hand and measure the backlash of the transfer ring gear and transfer driven pinion.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


NOTICE:

Measure the ring gear at 3 or more locations.



c.

If the result is not within the specified range, select a No. 1 ring gear mounting case washer (for backlash adjustment) and a No. 2 transfer ring gear mounting case washer (for preload adjustment) from the table below and reinstall them to bring the result within the specified range.

HINT:
·

If the backlash is small, select a thick washer for the No. 1 ring gear mounting case washer (for backlash adjustment) and a thin washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).

·

If the backlash is large, select a thin washer for the No. 1 ring gear mounting case washer (for backlash adjustment) and a thick washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).



No. 1 Ring Gear Mounting Case Washer (for backlash adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36265-42010 1.96 to 1.98 mm (0.0772 to 0.0779 in.) A0 36265-42210 2.36 to 2.38 mm (0.0930 to 0.0937 in.) C0
36265-42020 1.98 to 2.00 mm (0.0780 to 0.0787 in.) A1 36265-42220 2.38 to 2.40 mm (0.0938 to 0.0944 in.) C1
36265-42030 2.00 to 2.02 mm (0.0788 to 0.0795 in.) A2 36265-42230 2.40 to 2.42 mm (0.0945 to 0.0952 in.) C2
36265-42040 2.02 to 2.04 mm (0.0796 to 0.0803 in.) A3 36265-42240 2.42 to 2.44 mm (0.0953 to 0.0960 in.) C3
36265-42050 2.04 to 2.06 mm (0.0804 to 0.0811 in.) A4 36265-42250 2.44 to 2.46 mm (0.0961 to 0.0968 in.) C4
36265-42060 2.06 to 2.08 mm (0.0812 to 0.0818 in.) A5 36265-42260 2.46 to 2.48 mm (0.0969 to 0.0976 in.) C5
36265-42070 2.08 to 2.10 mm (0.0819 to 0.0826 in.) A6 36265-42270 2.48 to 2.50 mm (0.0977 to 0.0984 in.) C6
36265-42080 2.10 to 2.12 mm (0.0827 to 0.0834 in.) A7 36265-42280 2.50 to 2.52 mm (0.0985 to 0.0992 in.) C7
36265-42090 2.12 to 2.14 mm (0.0835 to 0.0842 in.) A8 36265-42290 2.52 to 2.54 mm (0.0993 to 0.0999 in.) C8
36265-42100 2.14 to 2.16 mm (0.0843 to 0.0850 in.) A9 36265-42300 2.54 to 2.56 mm (0.1000 to 0.1007 in.) C9
36265-42110 2.16 to 2.18 mm (0.0851 to 0.0858 in.) B0 36265-42310 2.56 to 2.58 mm (0.1008 to 0.1015 in.) D0
36265-42120 2.18 to 2.20 mm (0.0859 to 0.0866 in.) B1 36265-42320 2.58 to 2.60 mm (0.1016 to 0.1023 in.) D1
36265-42130 2.20 to 2.22 mm (0.0867 to 0.0874 in.) B2 36265-42330 2.60 to 2.62 mm (0.1024 to 0.1031 in.) D2
36265-42140 2.22 to 2.24 mm (0.0875 to 0.0881 in.) B3 36265-42340 2.62 to 2.64 mm (0.1032 to 0.1039 in.) D3
36265-42150 2.24 to 2.26 mm (0.0882 to 0.0889 in.) B4 36265-42350 2.64 to 2.66 mm (0.1040 to 0.1047 in.) D4
36265-42160 2.26 to 2.28 mm (0.0890 to 0.0897 in.) B5 36265-42360 2.66 to 2.68 mm (0.1048 to 0.1055 in.) D5
36265-42170 2.28 to 2.30 mm (0.0898 to 0.0905 in.) B6 36265-42370 2.68 to 2.70 mm (0.1056 to 0.1062 in.) D6
36265-42180 2.30 to 2.32 mm (0.0906 to 0.0913 in.) B7 36265-42380 2.70 to 2.72 mm (0.1063 to 0.1070 in.) D7
36265-42190 2.32 to 2.34 mm (0.0914 to 0.0921 in.) B8 36265-42390 2.72 to 2.74 mm (0.1071 to 0.1078 in.) D8
36265-42200 2.34 to 2.36 mm (0.0922 to 0.0929 in.) B9 36265-42400 2.74 to 2.76 mm (0.1079 to 0.1086 in.) D9


No. 2 Transfer Ring Gear Mounting Case Washer (for preload adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36266-52010 1.17 to 1.19 mm (0.0461 to 0.0468 in.) A0 36266-52230 1.61 to 1.63 mm (0.0634 to 0.0641 in.) C2
36266-52020 1.19 to 1.21 mm (0.0469 to 0.0476 in.) A1 36266-52240 1.63 to 1.65 mm (0.0642 to 0.0649 in.) C3
36266-52030 1.21 to 1.23 mm (0.0477 to 0.0484 in.) A2 36266-52250 1.65 to 1.67 mm (0.0650 to 0.0657 in.) C4
36266-52040 1.23 to 1.25 mm (0.0485 to 0.0492 in.) A3 36266-52260 1.67 to 1.69 mm (0.0658 to 0.0665 in.) C5
36266-52050 1.25 to 1.27 mm (0.0493 to 0.0499 in.) A4 36266-52270 1.69 to 1.71 mm (0.0666 to 0.0673 in.) C6
36266-52060 1.27 to 1.29 mm (0.0500 to 0.0507 in.) A5 36266-52280 1.71 to 1.73 mm (0.0674 to 0.0681 in.) C7
36266-52070 1.29 to 1.31 mm (0.0508 to 0.0515 in.) A6 36266-52290 1.73 to 1.75 mm (0.0682 to 0.0688 in.) C8
36266-52080 1.31 to 1.33 mm (0.0516 to 0.0523 in.) A7 36266-52300 1.75 to 1.77 mm (0.0689 to 0.0696 in.) C9
36266-52090 1.33 to 1.35 mm (0.0524 to 0.0531 in.) A8 36266-52310 1.77 to 1.79 mm (0.0697 to 0.0704 in.) D0
36266-52100 1.35 to 1.37 mm (0.0532 to 0.0539 in.) A9 36266-52320 1.79 to 1.81 mm (0.0705 to 0.0712 in.) D1
36266-52110 1.37 to 1.39 mm (0.0540 to 0.0547 in.) B0 36266-52330 1.81 to 1.83 mm (0.0713 to 0.0720 in.) D2
36266-52120 1.39 to 1.41 mm (0.0548 to 0.0555 in.) B1 36266-52340 1.83 to 1.85 mm (0.0721 to 0.0728 in.) D3
36266-52130 1.41 to 1.43 mm (0.0556 to 0.0562 in.) B2 36266-52350 1.85 to 1.87 mm (0.0729 to 0.0736 in.) D4
36266-52140 1.43 to 1.45 mm (0.0563 to 0.0570 in.) B3 36266-52360 1.87 to 1.89 mm (0.0737 to 0.0744 in.) D5
36266-52150 1.45 to 1.47 mm (0.0571 to 0.0578 in.) B4 36266-52370 1.89 to 1.91 mm (0.0745 to 0.0751 in.) D6
36266-52160 1.47 to 1.49 mm (0.0579 to 0.0586 in.) B5 36266-52380 1.91 to 1.93 mm (0.0752 to 0.0759 in.) D7
36266-52170 1.49 to 1.51 mm (0.0587 to 0.0594 in.) B6 36266-52390 1.93 to 1.95 mm (0.0760 to 0.0767 in.) D8
36266-52180 1.51 to 1.53 mm (0.0595 to 0.0602 in.) B7 36266-52400 1.95 to 1.97 mm (0.0768 to 0.0775 in.) D9
36266-52190 1.53 to 1.55 mm (0.0603 to 0.0610 in.) B8 36266-52410 1.97 to 1.99 mm (0.0776 to 0.0783 in.) E0
36266-52200 1.55 to 1.57 mm (0.0611 to 0.0618 in.) B9 36266-52420 1.99 to 2.01 mm (0.0784 to 0.0791 in.) E1
36266-52210 1.57 to 1.59 mm (0.0619 to 0.0625 in.) C0 36266-52430 2.01 to 2.03 mm (0.0792 to 0.0799 in.) E2
36266-52220 1.59 to 1.61 mm (0.0626 to 0.0633 in.) C1 - - -



Hide 15.ADJUST TOTAL PRELOAD

a.
C130167
2.417,0.667 2.031,0.667 false 2.469,0.594 2.781,0.75 0.313,0.156 10 *1 0.167,0.177 0.625,0.375 0.458,0.198 10 90°
*1 Nut


Install a nut to the stud bolt.

HINT:

Use a nut that is used for installing the propeller shaft.



b.

Using a torque wrench, measure the total preload (starting torque) with the teeth of the driven pinion and ring gear in contact.

Total preload (starting torque):
Item Specified Condition
New bearing (with anti-rust oil) Driven pinion preload + 0.31 to 0.81 N*m (3.17 to 8.25 kgf*cm, 2.75 to 7.16 in.*lbf)
Reused bearing (when coated with gear oil) Driven pinion preload + 0.23 to 0.81 N*m (2.35 to 8.25 kgf*cm, 2.04 to 7.16 in.*lbf)


NOTICE:

Measure the preload after rotating the bearing several times in the forward and backward directions to make sure the bearing is operating correctly.


HINT:

Install the torque wrench as shown in the illustration.



c.

If the result is not within the specified range, select a No. 2 transfer ring gear mounting case washer (for preload adjustment) from the table below and reinstall it to bring the result within the specified range.

HINT:
·

If the preload is small, select a thick washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).

·

If the preload is large, select a thin washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).



No. 2 Transfer Ring Gear Mounting Case Washer (for preload adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36266-52010 1.17 to 1.19 mm (0.0461 to 0.0468 in.) A0 36266-52230 1.61 to 1.63 mm (0.0634 to 0.0641 in.) C2
36266-52020 1.19 to 1.21 mm (0.0469 to 0.0476 in.) A1 36266-52240 1.63 to 1.65 mm (0.0642 to 0.0649 in.) C3
36266-52030 1.21 to 1.23 mm (0.0477 to 0.0484 in.) A2 36266-52250 1.65 to 1.67 mm (0.0650 to 0.0657 in.) C4
36266-52040 1.23 to 1.25 mm (0.0485 to 0.0492 in.) A3 36266-52260 1.67 to 1.69 mm (0.0658 to 0.0665 in.) C5
36266-52050 1.25 to 1.27 mm (0.0493 to 0.0499 in.) A4 36266-52270 1.69 to 1.71 mm (0.0666 to 0.0673 in.) C6
36266-52060 1.27 to 1.29 mm (0.0500 to 0.0507 in.) A5 36266-52280 1.71 to 1.73 mm (0.0674 to 0.0681 in.) C7
36266-52070 1.29 to 1.31 mm (0.0508 to 0.0515 in.) A6 36266-52290 1.73 to 1.75 mm (0.0682 to 0.0688 in.) C8
36266-52080 1.31 to 1.33 mm (0.0516 to 0.0523 in.) A7 36266-52300 1.75 to 1.77 mm (0.0689 to 0.0696 in.) C9
36266-52090 1.33 to 1.35 mm (0.0524 to 0.0531 in.) A8 36266-52310 1.77 to 1.79 mm (0.0697 to 0.0704 in.) D0
36266-52100 1.35 to 1.37 mm (0.0532 to 0.0539 in.) A9 36266-52320 1.79 to 1.81 mm (0.0705 to 0.0712 in.) D1
36266-52110 1.37 to 1.39 mm (0.0540 to 0.0547 in.) B0 36266-52330 1.81 to 1.83 mm (0.0713 to 0.0720 in.) D2
36266-52120 1.39 to 1.41 mm (0.0548 to 0.0555 in.) B1 36266-52340 1.83 to 1.85 mm (0.0721 to 0.0728 in.) D3
36266-52130 1.41 to 1.43 mm (0.0556 to 0.0562 in.) B2 36266-52350 1.85 to 1.87 mm (0.0729 to 0.0736 in.) D4
36266-52140 1.43 to 1.45 mm (0.0563 to 0.0570 in.) B3 36266-52360 1.87 to 1.89 mm (0.0737 to 0.0744 in.) D5
36266-52150 1.45 to 1.47 mm (0.0571 to 0.0578 in.) B4 36266-52370 1.89 to 1.91 mm (0.0745 to 0.0751 in.) D6
36266-52160 1.47 to 1.49 mm (0.0579 to 0.0586 in.) B5 36266-52380 1.91 to 1.93 mm (0.0752 to 0.0759 in.) D7
36266-52170 1.49 to 1.51 mm (0.0587 to 0.0594 in.) B6 36266-52390 1.93 to 1.95 mm (0.0760 to 0.0767 in.) D8
36266-52180 1.51 to 1.53 mm (0.0595 to 0.0602 in.) B7 36266-52400 1.95 to 1.97 mm (0.0768 to 0.0775 in.) D9
36266-52190 1.53 to 1.55 mm (0.0603 to 0.0610 in.) B8 36266-52410 1.97 to 1.99 mm (0.0776 to 0.0783 in.) E0
36266-52200 1.55 to 1.57 mm (0.0611 to 0.0618 in.) B9 36266-52420 1.99 to 2.01 mm (0.0784 to 0.0791 in.) E1
36266-52210 1.57 to 1.59 mm (0.0619 to 0.0625 in.) C0 36266-52430 2.01 to 2.03 mm (0.0792 to 0.0799 in.) E2
36266-52220 1.59 to 1.61 mm (0.0626 to 0.0633 in.) C1 - - -



Hide 16.ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.

Rotate the transfer output shaft sub-assembly several times in the forward and backward directions.


b.

Remove the transfer ring gear and check the tooth contact.

C247128
0.188,1.073 0.5,1.271 0.313,0.198 10 *a 2.656,0.073 2.969,0.271 0.313,0.198 10 *b 2.688,1.823 3,2.021 0.313,0.198 10 *e 4.917,1.802 5.229,2 0.313,0.198 10 *f 4.833,0.115 5.146,0.313 0.313,0.198 10 *c 3.75,1.438 4.063,1.635 0.313,0.198 10 *d 3.75,3.24 4.063,3.438 0.313,0.198 10 *g
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from to the ring gear (*e, *f) - -


NOTICE:
·

Check the tooth contact at 4 or more locations on the transfer ring gear.

·

When replacing washers (adjusting the backlash, preload or tooth contact pattern), reapply a coat of Prussian Blue.



HINT:

The Prussian Blue pattern indicates the tooth contact points.



c.

In instances of face contact or flank contact, perform the following procedure.

i.

Move and adjust the transfer ring gear using the No. 2 transfer ring gear mounting case washer (for preload adjustment) and the No. 1 ring gear mounting case washer (for backlash adjustment).



d.

In instances of heel contact or toe contact, perform the following procedure.

i.

Select a transfer output shaft washer (for tooth contact adjustment) from the table below, and move and adjust the transfer driven pinion.

Transfer Output Shaft Washer (for tooth contact adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36275-52010 1.01 to 1.03 mm (0.0398 to 0.0405 in.) 01 36275-52150 1.29 to 1.31 mm (0.0508 to 0.0515 in.) 15
36275-52020 1.03 to 1.05 mm (0.0406 to 0.0413 in.) 02 36275-52160 1.31 to 1.33 mm (0.0516 to 0.0523 in.) 16
36275-52030 1.05 to 1.07 mm (0.0414 to 0.0421 in.) 03 36275-52170 1.33 to 1.35 mm (0.0524 to 0.0531 in.) 17
36275-52040 1.07 to 1.09 mm (0.0422 to 0.0429 in.) 04 36275-52180 1.35 to 1.37 mm (0.0532 to 0.0539 in.) 18
36275-52050 1.09 to 1.11 mm (0.0430 to 0.0437 in.) 05 36275-52190 1.37 to 1.39 mm (0.0540 to 0.0547 in.) 19
36275-52060 1.11 to 1.13 mm (0.0438 to 0.0444 in.) 06 36275-52200 1.39 to 1.41 mm (0.0548 to 0.0555 in.) 20
36275-52070 1.13 to 1.15 mm (0.0445 to 0.0452 in.) 07 36275-52210 1.41 to 1.43 mm (0.0556 to 0.0562 in.) 21
36275-52080 1.15 to 1.17 mm (0.0453 to 0.0460 in.) 08 36275-52220 1.43 to 1.45 mm (0.0563 to 0.0570 in.) 22
36275-52090 1.17 to 1.19 mm (0.0461 to 0.0468 in.) 09 36275-52230 1.45 to 1.47 mm (0.0571 to 0.0578 in.) 23
36275-52100 1.19 to 1.21 mm (0.0469 to 0.0476 in.) 10 36275-52240 1.47 to 1.49 mm (0.0579 to 0.0586 in.) 24
36275-52110 1.21 to 1.23 mm (0.0477 to 0.0484 in.) 11 36275-52250 1.49 to 1.51 mm (0.0587 to 0.0594 in.) 25
36275-52120 1.23 to 1.25 mm (0.0485 to 0.0492 in.) 12 36275-52260 1.51 to 1.53 mm (0.0595 to 0.0602 in.) 26
36275-52130 1.25 to 1.27 mm (0.0493 to 0.0499 in.) 13 36275-52270 1.53 to 1.55 mm (0.0603 to 0.0610 in.) 27
36275-52140 1.27 to 1.29 mm (0.0500 to 0.0507 in.) 14 36275-52280 1.55 to 1.57 mm (0.0611 to 0.0618 in.) 28




e.

If the tooth contact has been adjusted, recheck the backlash, preload and tooth contact pattern.


Hide 17.REMOVE NO. 1 TRANSFER CASE COVER

a.
C130048

Remove the 8 bolts and No. 1 transfer case cover from the transfer case.


Hide 18.REMOVE TRANSFER RING GEAR

a.
C130050

Remove the transfer ring gear from the transfer case.


Hide 19.REMOVE REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

C130053

a.

Remove the 5 bolts and rear transfer output shaft sub-assembly from the transfer case.


Hide 20.INSTALL TRANSFER CASE STRAIGHT PIN

a.
C284184
2.979,0.958 3.333,1.146 0.354,0.188 10 false (A) 3.01,3.323 3.365,3.51 0.354,0.188 10 false (B)

Using a plastic-faced hammer, install straight pins to the locations shown in the illustration.

Drive in depth (A):

10.8 to 11.8 mm (0.426 to 0.464 in.)


Drive in depth (B):

6.5 to 7.5 mm (0.256 to 0.295 in.)



Hide 21.INSTALL REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

a.
C130057

Secure the rear transfer output shaft sub-assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a chisel and hammer, stake the transfer gear nut.

NOTICE:

Fully stake the transfer gear nut along the entire groove.



c.
C130053

Install the rear transfer output shaft sub-assembly to the transfer case with the 5 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Do not scratch, twist or break the O-ring.



Hide 22.INSTALL TRANSFER RING GEAR

a.
C130050

Install the transfer ring gear to the transfer case.


Hide 23.INSTALL NO. 1 TRANSFER CASE COVER

a.

Using a scraper, clean the seal packing from the transfer case and No. 1 transfer case cover and remove any oil using a cleaning solvent.

NOTICE:

Do not scratch the installation area.



b.
C268744
2.25,1.917 2.167,1.917 2.167,1.917 2.021,1.625 false 2.292,1.833 2.604,1.99 0.313,0.156 10 *1 0.177,0.667 0.333,0.865 0.156,0.198 10 A 1.354,1.167 1.667,1.323 0.313,0.156 10 30° 3.083,0.802 3.396,0.958 0.313,0.156 10 *a
*1 Seal Packing
*a Seal Width 2.0 to 3.0 mm (0.0788 to 0.118 in.)


Apply seal packing to the transfer case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Install the cover to the case within 10 minutes of application.

·

Start the application from inside the area marked A.

·

Overlap the seal packing at least 10 mm (0.394 in.) at the beginning and the end of application.




c.
C130048

Install the No. 1 transfer case cover with the 8 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 24.INSTALL TRANSFER CASE OIL SEAL

a.
C278966
0.75,4.104 0.948,4.104 0.948,4.104 1.406,3.417 true 0.875,0.594 1.115,0.594 1.115,0.594 1.49,1.26 true 0.615,3 1.073,3.198 0.458,0.198 10 false (A) 0.542,4.01 1,4.208 0.458,0.198 10 false *1 0.542,0.5 1,0.698 0.458,0.198 10 false SST
*1 Transfer Case Oil Seal


Using SST and a hammer, tap in a new transfer case oil seal as shown in the illustration.

SST
09316-60011  (09316-00011)

Drive in depth (A):

9.5 to 10.5 mm (0.375 to 0.413 in.)


NOTICE:
·

Tap the transfer case oil seal uniformly so that the transfer case oil seal is straight.

·

Do not tap the transfer case oil seal in too far.




Hide 25.INSTALL TRANSFER CASE OIL SEAL RH

a.
C156152
1.49,0.635 1.833,1 1.833,1 1.917,1 true 2.083,2.25 2.25,2 2.25,2 2.333,2 true 1.938,0.927 2.25,1.083 0.313,0.156 10 *1 1.875,0.583 2.188,0.74 0.313,0.156 10 (A) 2.458,1.938 2.771,2.115 0.313,0.177 10 SST
*1 Transfer Case Oil Seal RH


Using SST and a hammer, tap in a new transfer case oil seal RH as shown in the illustration.

SST
09316-60011  (09316-00011)

Drive in depth (A):

7.5 to 8.5 mm (0.296 to 0.334 in.)


NOTICE:
·

Tap the transfer case oil seal RH uniformly so that the transfer case oil seal RH is straight.

·

Do not tap the transfer case oil seal RH in too far.




Hide 26.INSTALL TRANSFER CASE BREATHER PLUG

C222932
2.167,0.75 2.667,1.667 2.667,1.667 2.75,1.667 true 2.792,1.594 3.25,1.792 0.458,0.198 10 SST

a.

Using SST, tap in a new transfer case breather plug until it meets the transfer case.

SST
09612-10093  (09612-10061)


Hide 27.INSTALL NO. 2 TRANSFER CASE PLUG

C284181

a.

Using a 10 mm socket hexagon wrench, install a new gasket and the No. 2 transfer case plug (filler plug).

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 28.INSTALL TRANSFER DRAIN PLUG

C284180

a.

Using a 10 mm socket hexagon wrench, install a new gasket and the transfer drain plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 29.INSTALL NO. 1 TRANSFER CASE PLUG

a.
C130044

Install a new gasket and the No. 1 transfer case plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 30.REMOVE TRANSFER ASSEMBLY

a.
C284178

Remove the transfer assembly from the overhaul attachment.


Hide 31.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.

Clean the bolt holes.


b.
C293225
2.26,1.052 2.448,1.052 2.448,1.052 2.802,1.49 true 3,1.667 3.313,1.865 0.313,0.198 10 false *a 2.083,0.969 2.396,1.167 0.313,0.198 10 false *b
*a Transfer Side
*b Toyota Genuine Adhesive 1324


Using 2 nuts, install the 4 stud bolts in the locations shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the shorter threaded part of each stud bolt to the transfer side.