Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.11
RM30B0U _56 Audio / Visual / Telematics _009403 AUDIO / VIDEO _0054849 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  DTC CHECK / CLEAR  


CHECK DTC (CHECK USING TECHSTREAM)


a.

Connect the Techstream to the DLC3.


b.

Engine start.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Navigation System / Trouble Codes.


e.

Check for DTCs, and then write them down.

Body Electrical > Navigation System > Trouble Codes
50001 212



CLEAR DTC (CLEAR USING TECHSTREAM)


a.

Connect the Techstream to the DLC3.


b.

Engine start.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Navigation System / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212


START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

Start diagnostic mode 15 seconds after engine started. Otherwise, some items cannot be checked.



a.
E269538

While pressing and holding the "AUDIO" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.


b.

Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.



FAILURE DIAGNOSIS


a.
E278177

Press the "Failure Diagnosis" switch on the "Service Menu" screen.


b.

The "Failure Diagnosis" will be displayed.



SYSTEM CHECK


a.
E282451

Press the "System Check" switch on the "Failure Diagnosis" screen.


b.

The "System Check Mode" screen will be displayed.



CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


a.
E282452
0.26,0.75 0.51,0.75 true 1.833,2 2,2 2,2 2.104,1.76 true 1.24,0.75 1.49,0.75 true 2.313,0.99 2.396,0.823 2.396,0.823 2.563,0.823 true 2.479,1.427 2.646,1.427 2.646,1.427 2.75,1.677 true 0.083,0.656 0.396,0.854 0.313,0.198 10 false *a 1.521,0.667 1.833,0.865 0.313,0.198 10 false *b 1.688,1.906 2,2.104 0.313,0.198 10 false *c 2.323,1.333 2.635,1.531 0.313,0.198 10 false *d 2.604,0.74 2.917,0.938 0.313,0.198 10 false *e

System check mode screen description

Screen Description
Display Content
*a: Device Name List No. 1
·

Device Name List No. 1 displays some of the devices that make up the audio and visual system

·

The names of the components from Device Name List No. 1 are shown in the following table


*b: Check Result Result codes for all devices are displayed
*c: Memory Clear
·

Present and history DTCs and registered connected device names are cleared

·

Press the "Memory CLR" switch for 3 seconds


*d: Recheck
·

A system check will be performed again after the memory is cleared

·

The "Recheck" switch will dim during a system check


*e: Device Name List No. 2
·

Device Name List No. 2 displays some of the devices that make up the audio and visual system

·

The names of the components from Device Name List No. 2 are shown in the following table



*a: Device Name List No. 1 Description
Name Component Connection Method
DA Radio and display receiver assembly -
EXT BOX* Satellite radio antenna assembly Communication line for LVDS

*: w/ SDARS System


*b: Check Result Description
Result Meaning Action
OK The device does not respond with a DTC -
DETAIL The device responds with a DTC Look up the DTC in "Unit Check Mode"
NCON* The device was previously present, but does not respond in diagnostic mode Check power supply wire harness of the device
NRES* The device responds in diagnostic mode, but gives no DTC information Check power supply wire harness of the device

*: w/ SDARS System


*e: Device Name List No. 2 Description
Name Component Connection Method
AUX/USB No. 1 stereo jack adapter assembly Vehicle wire harness


b.
E278180
0.333,0.917 0.667,0.917 false 0.344,0.677 0.677,0.677 false 0.854,0.167 1.052,0.167 1.052,0.167 1.333,0.615 true 1.708,0.167 1.542,0.167 1.542,0.167 1.458,0.417 true 2.01,1.021 2.177,1.25 2.177,1.25 2.344,1.25 false 2.625,1.75 2.792,1.979 2.792,1.979 2.958,1.979 false 0.156,0.833 0.469,1.031 0.313,0.198 10 false *d 0.156,0.583 0.469,0.781 0.313,0.198 10 false *c 0.677,0.083 0.99,0.281 0.313,0.198 10 false *b 1.74,0.073 2.052,0.271 0.313,0.198 10 false *a 2.396,1.167 2.708,1.365 0.313,0.198 10 false *e 3,1.885 3.313,2.083 0.313,0.198 10 false *f

Unit check mode screen description

Screen Description
Display Content
*a: Device name Target device
*b: History DTC Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC DTCs output in the service check are displayed.
*d: DTC DTC (Diagnostic Trouble Code)
*e: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
*f: Diagnosis clear switch Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (Both response to diagnostic system check result and the displayed data are cleared.).

HINT:
·

This screen is updated once per second.

·

A maximum of 6 DTCs can be displayed for history and present DTCs.




c.
E282453

Read the system check result.

i.

If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

NOTICE:

A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.


HINT:
·

When all results are "OK", this means that no DTCs are stored.

·

When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.







DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


a.
E282454

Clear DTCs

i.

Press the "Memory CLR" switch for 3 seconds.


ii.

Confirm that the check results are cleared.

HINT:
·

To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

·

When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.





b.
E282455

Recheck

i.

Press the "Recheck" switch.


ii.
E282456

Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

HINT:

When DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.





FINISH DIAGNOSTIC MODE


a.

There are 2 methods to end diagnostic mode. Use one of them.

i.

Turn the ignition switch off.


ii.

Press and hold the "Audio" switch for 3 seconds.