Home › Power Source / Network › 2AR-FE BATTERY / CHARGING › GENERATOR › from 2013.11
RM30B0U _57 Power Source / Network _009269 2AR-FE BATTERY / CHARGING _0054866 GENERATOR A

2AR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE GENERATOR PULLEY CAP

a.
A298989

Using a screwdriver, puncture the center of the generator pulley cap and pry it off.

NOTICE:

Do not reuse the generator pulley cap.



Hide 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.
A298990
1.708,1.01 2.063,1.729 2.063,1.729 2.24,1.729 false 0.688,1.885 0.875,1.885 0.875,1.885 0.958,1.458 false 2.313,1.646 2.979,1.844 0.667,0.198 10 SST (A) 0.156,1.813 0.823,2.01 0.667,0.198 10 SST (B)

Mount the generator assembly in a vise between aluminum plates.


b.

Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  


c.
A298991
1.844,0.531 2.094,0.25 2.094,0.25 2.292,0.25 false 2.115,0.792 2.313,0.948 2.313,0.948 2.542,0.948 false 2.365,0.167 3.042,0.354 0.677,0.188 10 SST (B) 2.604,0.854 3.281,1.042 0.677,0.188 10 SST (A) 1.833,1.813 2.146,1.969 0.313,0.156 10 *a
*a Hold
V100135

Turn


Use a wrench to hold SST (A) and turn SST (B) counterclockwise to loosen the generator pulley with clutch.


d.

Remove the generator pulley with clutch.


Hide 3.REMOVE GENERATOR REAR END COVER

a.
A302251

Place the generator on the generator pulley with clutch.


b.
A298992

Remove the 3 bolts and generator rear end cover.


c.
A192780

Remove the terminal insulator.


Hide 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A192781

Remove the 2 screws and generator brush holder assembly.


Hide 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A192782

Remove the 4 bolts.


b.
A192783
0.533,0.31 0.837,0.484 0.304,0.174 10 SST 1.583,0.78 1.028,0.404 1.028,0.404 0.902,0.404 false

Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


Hide 6.REMOVE GENERATOR BEARING COVER PACKING

a.
A284548

Remove the generator bearing cover packing.

NOTICE:

If the generator bearing cover packing breaks, remove all broken pieces.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A153384

Remove the generator rotor assembly from the generator drive end frame assembly.


Hide 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A192785

Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If the result is not as specified, replace the generator drive end frame bearing.


Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A192787

Remove the 4 screws and bearing retainer.


b.
A298993
2.271,1.927 1.698,1.156 false 2.552,1.927 2.271,1.927 2.271,1.927 1.708,1.354 false 2.615,1.865 3.073,2.063 0.458,0.198 10 SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)