Home › Engine / Hybrid System › 2AD-FTV ENGINE MECHANICAL › ENGINE UNIT
NM3090E _51 Engine / Hybrid System _008661 2AD-FTV ENGINE MECHANICAL _0048049 ENGINE UNIT DE DETAILS F

2AD-FTV ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

The cylinder block assembly is made of aluminum alloy.


b.

A water passage is provided between the cylinder bores. By allowing the water to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.


c.

The liners are the spiny-type, which are manufactured so that their casting exterior forms a large irregular surface in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps improve heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores.


d.

Crankshaft bearing caps with cylinder block lower cases are used to reduce noise and to increase the coupling rigidity with the crankshaft.


e.

Cast-iron is used as a material for part of the bearing journal of the crankshaft bearing cap, thus helping prevent deformation caused by high loads from the crankshaft.


f.

Plastic region tightening bolts are used for tightening the crankshaft bearing cap.

W100167C01
0.865,3.552 1.479,3.052 1.479,3.052 1.802,3.052 true 0.927,5.438 1.188,5.438 1.188,5.438 1.479,5.073 true 5.354,1.031 5.615,1.031 5.615,1.031 5.917,1.823 true 5.292,3.26 5.552,3.26 5.552,3.26 5.802,3.719 true 4.958,4.063 5.219,4.063 5.219,4.063 5.573,4.448 true 1.875,2.979 2.167,3.219 0.292,0.24 10 false *1 0.74,5.354 1.052,5.51 0.313,0.156 10 false *2 5.177,0.938 5.5,1.229 0.323,0.292 10 false *a 5.115,3.167 5.406,3.458 0.292,0.292 10 false *b 4.813,3.969 5.094,4.219 0.281,0.25 10 false *c 5.677,4.969 5.979,5.229 0.302,0.26 10 false *d 1.729,1.469 1.885,1.667 0.156,0.198 10 true A 1.188,1.271 1.344,1.469 0.156,0.198 10 true A
*1 Crankshaft Bearing Cap *2 Cylinder Block Lower Case
*a Water Passage *b Irregularly Shaped Outer Casting Surface of Liner
*c Liner *d A - A Cross Section


HINT:

Because the liner is thin, reboring is not possible.



g.

Air passage holes are provided on bulkheads of the cylinder block assembly and cylinder block lower case. As a result, the air at the bottom of the cylinder flows smoother, and pumping loss (back pressure at the bottom of the piston generated by the piston's reciprocating movement) has been reduced to improve the engine's output.

W100168C01
3.063,2.219 1.896,0.979 1.896,0.979 1.625,0.979 true 1.75,2.406 2.021,2.406 2.021,2.406 2.427,1.99 true 4.427,0.885 4.938,0.375 4.938,0.375 5.188,0.375 true 4.313,2 4.833,2.49 4.833,2.49 5.104,2.49 true 1.417,0.896 1.771,1.167 0.354,0.271 10 *a 5.24,0.302 5.615,0.583 0.375,0.281 10 *1 5.167,2.417 5.469,2.656 0.302,0.24 10 *2 1.552,2.323 1.906,2.594 0.354,0.271 10 *a
*1 Cylinder Block Assembly *2 Cylinder Block Lower Case
*a Air Passage Hole - -